Advertisement
Advertisement
Related Manuals for Absen iCon Series
Summary of Contents for Absen iCon Series
- Page 1 User Manual Shenzhen Absen Optoelectronic Co. Ltd.
-
Page 2: Table Of Contents
Table of content Safety Information Product Introduction About iCon series Product Specifications Product Installation Service and Maintenance... -
Page 3: Safety Information
This product may result in serious injury or death due to fire hazard, electric shock or on dropping. Please read this manual carefully before installing, powering up, operating and maintenance of this product. Follow safety instructions in this manual and on the product. If you have any questions, please seek help from Absen. - Page 4 Beware of Electric Shock! ⚫ To prevent electric shock the device must be properly grounded during installation. Do not ignore using the grounding plug, or else there is a risk of electric shock. ⚫ During a lightning storm, please disconnect the device’s power supply, or provide other suitable lightning protection.
- Page 5 Beware of Injury! ⚫ Warning: Wear a helmet to avoid injury. ⚫ Ensure any structures used to support, fix and connect the equipment, can withstand at least 10 times the weight of all the equipment. ⚫ When stacking products, please hold products firmly to prevent tipping or falling.
-
Page 6: Product Introduction
The iCon series has the following products: iCon C110, iCon C138, iCon C165 and iCon C220. In the future, according to market demand, other specifications will be introduced: iCon E110, iCon E138, iCon E165, iCon E192. - Page 9 iCon C110/ iCon E110 Product Specifications Parameters iCon C110 iCon E110 Pixels SMD0808 SMD1010 Pixel Pitch (mm) 1.27 1.58 Cabinet Pixels 480×270 384*216 Pixel Density (Pixels / m 619414 396424 Physical Parameters Module size (L × W)/(mm) 305×343 Cabinet size (L × W × H)/(mm) 610×343×61 Cabinet Material Die-cast Aluminum...
- Page 10 iCon C138/ iCon E138 Product Specifications Parameters iCon C138 iCon E138 Pixels SMD1010 Pixel Pitch (mm) 1.58 Cabinet Pixels 384×216 320×180 Pixel Density (Pixels / m 396424 275295 Physical Parameters Module size (L × W)/(mm) 305×343 Cabinet size (L × W × H)/(mm) 610×343×61 610×343×61 Cabinet Material...
- Page 11 iCon C165/ iCon E165 Product Specifications Parameters iCon C165 iCon E165 Pixels SMD1010 SMD2121 Pixel Pitch (mm) 2.54 Cabinet Pixels 320×180 240×135 Pixel Density (Pixels / m 275295 154853 Physical Parameters Module size (L × W)/(mm) 305×343 305×343 Cabinet size (L × W × H)/(mm) 610×343×61 610×343×61 Cabinet Material...
- Page 12 iCon E192/ iCon C220 Product Specifications Parameters iCon E192 iCon C220 Pixels SMD2121 Pixel Pitch (mm) 2.54 Cabinet Pixels 240×135 240×135 Pixel Density (Pixels / m 154853 154853 Physical Parameters Module size (L × W)/(mm) 305×343 305×343 Cabinet size (L × W × H)/(mm) 610×343×61 610×343×61 Cabinet Material...
- Page 13 2. Cabinet dimension figure 3. Module dimension figure...
- Page 14 Product Components 2.1 Cabinet Introduction 2.2 HDMI cable for vertical connections in between the cabinets（0.5m）...
- Page 15 2.3 HDMI cable connections in between the cabinets(0.95m) 2.4 Power Cable 1 for vertical connections in between the cabinets: 0.26 m long; Power Cable 2 for vertical connections in between the cabinets: 0.5 m long. 2.5 Main Power Cable, 10 m long，2.5mm² 2.6 Main HDMI cable,5m long...
-
Page 16: Product Installation
Product Installation The product is suitable for various forms of installation, including front installation & rear installation, rigging. Use allen wrench keys to lock the coffin locks either from the front or the back. ⚫ iCon C138、E138 installation C138, E138 screen body plus edge size: 3100x1769mm Step 1: Fix the wall connector The position is: the distance from the end face of the beam is 100mm;... - Page 17 Step 3: the left and right beams are connected. Install the upper and lower slot joints, a total of 3, use the 3mm hex wrench to screw in, the front side does not install the slot connector, because the front may need to put the T-nut to fix the hanging plate.
- Page 18 Step 5: T-nuts and large flat head screws M6x10 are screwed into all the waist holes of the hanging plate, as shown below: Large flat head screw M6x10 T-nut 中间挂 Middle hanging board or 板 side hanging board Note: First screw all T-nuts and screws into the middle and side hanging plate waist holes. Step 6: Fix the first side hanging plate to the beam, and align the side of the hanging plate with the cross section of the beam.
- Page 19 Step 7: Install the side hanging plate and the middle hanging plate from left to right. Step 8: Put in the box and lock it.
- Page 20 Step 9: Install the border and corner. Install from the bottom up, pay attention to the large frame screw M6x10 fixed frame to the box. Step 10: Fixed distribution box, ship type switch, etc. The position is the bottom of the cabinet.
- Page 21 ⚫ iCon C165、E165 installation ⚫ iCon E192 installation...
- Page 22 ⚫ iCon C220 installation...
- Page 23 Haring installation： Using span sets or steel cables to attach the bumpers to the truss or the steel structure. Connect the bumpers together using the metal connectors and make sure they are level. Cabinet installation Assemble the cabinets from top down, layer by layer, align the coffin locks with the corresponding holes on the bumpers.
- Page 25 During installation, make sure all the coffin locks are tightened in the direction of arrow as shown in the illustration.
- Page 26 Basic Wiring Overview for Installation Preparation before cabling Before supplying power and signal source to the screen, please check power and data cables connections carefully and make sure they are wired correctly. Use a multimeter to test the L, N and PE lines in AC power input port and make sure the tree lines are not short-circuited.
- Page 27 Power Cabling AC IN A single 3*2.5mm screen power cable can carry up to 32 cabinets, ie iCon C110/ iCon E110/ iCon C138/ iCon E138 screen comes standard with 1 3*2.5mm screen power cord, iCon C165/ iCon E165/iCon E192/ iCon C220 screen comes standard with 2 3*2.5mm joint power cables.
- Page 28 HDMI Cabling Notes: The signal line adopts HDMI cable, and the "S" type is connected up and down. Please calculate the resolution according to each box pixel. Each HDMI cable can control up to 1920*1080 pixels.
-
Page 29: Service And Maintenance
Maintenance Preparation Tools Screwdriver, multi-meter, module front service tool, etc. Module Front Service Step 1: Rotate two rotation handles on module front service tool clockwise all the way. Step 2: Place the front service tool onto the module tightly and rotate the two rotation handles counterclockwise all the way. - Page 30 Test for Short Circuit After finishing cabling the cabinets, use a multi-meter to test the AC input (L/N/PE) and DC output (VCC/GND) to determine whether there is a short circuit. If a short circuit has been found, please examine the circuit carefully. Power up the cabinets only after making sure all the circuits are working properly...
- Page 31 All rights reserved by Shenzhen Absen Optoelectronic Co., Ltd. Shenzhen Absen Optoelectronic Co., Ltd. reserves the rights to modify contents without any further notice. Shenzhen Absen Optoelectronic Co., Ltd. 18-20F Building 3A, Cloud Park, Bantian, Longgang District, Shenzhen 518129, P.R.China T: +86-755-89747399 absen@absen.com...
Need help?
Do you have a question about the iCon Series and is the answer not in the manual?
Questions and answers