Advertisement
Available languages
Available languages
• The horizontal detection range is approximately 120°. This range applies for installation heights of 1.8 to
9 m. Depending on the ambient conditions, the actual range may be shorter.
• The socket (1) on the front of the adapter plug must be underneath the PIR sensor when the adapter plug
is installed.
When connecting a light with a power rating of more than 60 W, the distance between the light
and the PIR sensor (6) must be at least 60 cm. Use an extension cable to connect the light.
Configuring the settings for the PIR sensor
Configure the sensitivity of the sensor. The registering of a
movement by the sensor depends on the distance from the
moving object. The PIR detection angle is 120° (horizontal) and
100 ° (vertical). Configure the reaction distance by turning the
SENS control towards + (plus) or - (minus).
- Turn the SENS control (3) clockwise (towards "+") to increase the reaction distance.
- Turn the SENS control anticlockwise (towards "-") to decrease the reaction distance.
- Configure the switch-on duration. The connected appliance will switch on for the preset duration when a
moving object is detected. You can choose a duration between 10 seconds and 15 minutes. Configure
the switch-on duration by moving the TIME control (4).
- Turn the TIME control clockwise to increase the switch-on duration.
- Turn the TIME control anticlockwise to decrease the switch-on duration.
• Configure the activation brightness (ambient brightness). When the ambient brightness reaches the preset
level, the PIR sensor will be activated, and the socket on the adapter plug will switch on when the sensor
detects a source of heat.
- Configure the activation brightness by turning the LUX control (5) towards
- Turn the LUX control clockwise (in the direction of the sun symbol
brightness.
- Turn the LUX control anticlockwise (in the direction of (3)) to decrease the activation brightness.
Testing the function of the PIR motion sensor
Test the PIR motion sensor settings that you just configured.
- To test the switch-on duration, connect a light to the adapter plug, activate the PIR sensor (6), and then
measure the time until the light switches off.
- To test the detection range, connect a light to the adapter plug, set the switch-off duration to the minimum
setting, and then move to and fro around the PIR sensor (6) at different distances.
- To test the activation brightness, connect a light to the adapter plug and move around the detection
area in the dark.
Troubleshooting
• The connected appliance doesn't switch on.
- Check the voltage and cabling of the appliance (if a cable is present).
- Check the appliance.
- Check the activation brightness.
• Motion detection is poor.
- Check if the ambient temperature is too high.
- Ensure that there are no obstructions that may prevent the sensor from detecting sources of heat.
- Check the reaction distance.
- Check that there are no induction sources within range of the sensor.
- Check the installation height.
• The adapter does not switch off the appliance automatically.
- Is there a permanent source of heat within range of the sensor? If so, remove the source of heat and
try again.
- Check whether the switch-off duration is set to the maximum setting.
- Check that the mains voltage is correct.
Care and cleaning
• Before cleaning the adapter plug, disconnect it from the mains socket, and then disconnect the appliance
from the adapter plug.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may damage the
housing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.
Disposal
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage ................................ 220–240 V/AC, 50/60 Hz
Internal fuse .......................................... 6 A (not replaceable)
Power rating of connected appliance .. Max. 1200 W (bulb) / 300 W (LED light) (min. 1 W for LED light)
Protection rating ................................... IP20
Horizontal detection angle .................... 120°
Vertical detection angel ........................ 100°
PIR range ............................................ 2–9 m (< 24 °C)
Activation brightness ........................... 3–2000 lx (adjustable)
Switch-on duration ............................... Approx. 10 ± 3 secs to 15 ± 2 mins (adjustable)
Installation height .................................. 1–1.8 m
Operating/storage conditions ................ -20 to +40 ºC, <93 %
Dimensions (W x H x D) ....................... 53 x 99 x 77 mm (depth with plug)
Weight .................................................. 116 g
Switching contact .................................. 1-pole (relay)
(daylight) or (3) (darkness).
) to increase the activation
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
Electronic devices are recyclable waste and must not be placed in household waste. Always
dispose of the product according to the relevant statutory regulations.
relative humidity (non-condensing)
*1588385_v3_0719_02_DS_m_3L_(1)
Advertisement
