Advertisement
Quick Links
Advertisement
Related Manuals for Harman REVEL PERFORMA3 B112V2
Summary of Contents for Harman REVEL PERFORMA3 B112V2
- Page 1 B112V2/B110V2 Subwoofer Quick Start Guide...
-
Page 2: Table Of Contents
TABLE OF CONTENTS About Revel Performa3V2 Subwoofers ........................... 2 B112V2/B110V2 Overview ............................... 3 Subwoofer Placement Considerations............................. 4 Placing a Single Subwoofer, Placing Two Subwoofers, Placing Four Subwoofers Making Connections ................................6 Connecting to a Surround Processor with an Internal Crossover, Connecting to a Stereo Preamplifier, Connecting Multiple Subwoofers, Trigger and Power Connections Caring for Your Subwoofer............................... -
Page 3: B112V2/B110V2 Overview
B112V2/B110V2 OVERVIEW (Note: B112V2 and B110V2 rear panels are identical) Input Connectors (Balanced XLR) Input Connectors (Unbalanced RCA) Subwoofer Gain (Volume) Control Low Pass Crossover Frequency Control PEQ Frequency Control PEQ Bandwidth Control PEQ Level Control Power Mode Switch Power Indicator LED Power Switch Phase Power Cord Connector... -
Page 4: Subwoofer Placement Considerations
SUBWOOFER PLACEMENT PLACING A SINGLE SUBWOOFER CONSIDERATIONS When installing a single subwoofer, experiment with different locations to find the one that produces the best results throughout your room’s When using subwoofers within the limited confines of a typical home seating area. As in the previous examples, placing the subwoofer in a theater room, the reflections, standing waves and absorptions within corner will produce the fewest number of deep response dips, which the room will create peaks and dips in the bass response that can vary... - Page 5 PLACING FOUR SUBWOOFERS Rooms with multiple seating rows When installing four subwoofers, place each one in a room corner. In Placing one subwoofer in a front corner and the other subwoofer in the rooms with more than four corners, use the four corners closest to the rear corner on the same side will produce the most consistent bass listening area.
-
Page 6: Making Connections
MAKING CONNECTIONS CAUTION: Never make or break connections unless all system components are powered off. CONNECTING TO AN AV SURROUND RECEIVER OR PROCESSOR WITH AN INTERNAL CROSSOVER If you are connecting to a surround processor with a low-pass filtered subwoofer output, connect the subwoofer as shown below. You can make either a balanced (XLR) or unbalanced (RCA) connection to either the subwoofer’s left or right input connector. - Page 7 CONNECTING TO A STEREO RECEIVER, AMPLIFIER OR PREAMPLIFIER If you are connecting to a stereo device, connect the subwoofer as shown below. Stereo components rarely have subwoofer outputs. Use them if they are available; otherwise, be sure to use a Y-connector for the left output and one for the right output, connecting the subwoofer input to one side of each Y and the input for the left or right main speaker amplifier to the other side of the Y for proper main speaker operation.
- Page 8 CONNECTING MULTIPLE SUBWOOFERS When installing more than one Performa3V2 subwoofer, connect “Y” connectors to the receiver or processor’s outputs. If your source component has two subwoofer output jacks you can connect up to four subwoofers as illustrated on this page. Be sure to set up and adjust each subwoofer PEQ separately, then adjust all of the subwoofer levels and crossover frequencies together to blend to the main speaker systems.
-
Page 9: Caring For Your Subwoofer
TRIGGER AND POWER CONNECTIONS Trigger In/Out Connectors If you want your subwoofer(s) to turn on along with another component that supplies a trigger voltage, use a mono 3.5mm cable (not supplied) to connect the 12V DC Trigger In connector to the trigger voltage out connector of the other component. -
Page 10: Specifications
SPECIFICATIONS B112V2/B110V2 Type: Powered subwoofer Low-frequency transducer: Coated paper/pulp cone (12" – B112V2; 10" – B110V2) with 50mm two-layer copper voice coil, vented ceramic 5 magnet assembly and vented die-cast aluminum frame Amplifier power: 1,000 watts (RMS), 2,000 watts (peak) Input sensitivity/impedance: 400mV (full power)/20k ohms (balanced);... - Page 11 8500 Balboa Boulevard, Northridge, CA 91329 USA © 2018 HARMAN International Industries, Incorporated. All rights reserved. Revel and the Revel logo are trademarks of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Nomex is a registered trademark of E. I. du Pont de Nemours and Company.