Menu Parameter Descriptions; Audio Menu; Utilities Menu - Shure AXIENT ADX1M User Manual

Menu Parameters
The Main menu organizes the available transmitter parameters into three
sub-menus:
• Radio
• Audio
• Utilities
Tip: Use the arrow buttons to scroll between the sub-menus.
Radio
Tips for Editing Menu Parameters
• To access the menu options from the home screen, press O . Use the
arrow buttons to access additional menus and parameters.
• A menu parameter will blink when editing is enabled
• To increase, decrease or change a parameter, use the arrow buttons
• To save a menu change, press O
• To exit a menu without saving a change, press X

Menu Parameter Descriptions

Radio Menu
Freq
Press the O button to enable editing of a group (G:) channel
(C:) or frequency (MHz). Use the arrow buttons to adjust the
values. To edit the frequency, press the O button once to edit
the first 3 digits, or twice to edit the second 3 digits.
Power
Higher RF power settings can extend the range of the
transmitter.
Note: Higher RF power settings decrease battery runtime.
Output
Sets the RF output to On or Mute.
- On: RF signal is active
- Mute: RF signal is inactive

Audio Menu

Offset
Adjust Offset level to balance mic levels when using two
transmitters or when assigning multiple transmitters to
receiver slots. Adjustment range: -12 dB to +21 dB.
Polarity
Selectable polarity assignment for audio input connector:
- Pos: Positive pressure on microphone diaphragm produces posi-
tive voltage on pin 2 (with respect to pin 3 of XLR output) and the
tip of the TRS output.
- Neg: Positive pressure on microphone diaphragm produces nega-
tive voltage on pin 2 (with respect to pin 3 of XLR output) and the
tip of the TRS output.
Mute
When enabled, the power button is configured as a mute
switch for the audio output. Press the power button to mute
or un-mute the audio. Exit mute mode to return the power
button to its normal functionality.
Tone Gen
Transmitter will generate a continuous test tone:
- Freq: The tone can be set to 400 Hz or 1000 Hz.
- Level: Adjusts of the output level of the test tone.
Main
Menu Map
Main Menu

Utilities Menu

Device ID
Assign a device ID of up to 9 letters or numbers.
Locks
- None: The controls are unlocked
- Power: The power switch is locked
- Menu: The menu parameters are locked
- All: The power switch and menu parameters are locked
Locks the transmitter controls and power switch.
Link Info
Displays the following information about the link between a transmitter and receiver:
- Not Linked: The transmitter is not linked to a receiver
- Linked: The transmitter is linked to a receiver. Select Unlink? to free the transmitter from the
receiver link.
- Unlinked: The transmitter is not linked to a receiver
SL Test
ShowLink test tool to measure the boundaries of ShowLink coverage.
Marker
When enabled, press the enter button to drop a marker in Wireless Workbench.
Battery
Displays battery information:
- Battery Life: Runtime reported in bar display and time (hours:minutes)
- Charge: Percentage of charge capacity
- Health: Percentage of current battery health
- Cycle Count: Total of the number of charging cycles for the installed battery
- Temperature: Battery temperature reported in Celsius and Fahrenheit
Talk Sw
Indicates the status of the talk switch.
Identify
When enabled, Identify flashes the display of the receiver linked to the
transmitter.
About
Displays the following transmitter information:
- Model Displays the model number
- Band Displays the tuning band of the transmitter
- FW Version Installed firmware
- HW Version Hardware version
- Serial Num Serial number
Reset All
Restores all transmitter parameters to factory settings.
10
Radio
Freq
Power
Output
Audio
O set
Polarity
Mute
Tone Gen
Utilities
Device ID
Locks
Link Info
SL Test
Marker
Battery
Talk Sw
Identify
About
Reset All