Kinderkraft ALL ROAD User Manual page 17

 The parking device shall be engaged when placing and removing the children
 The maximum basket load is 5 kg.
 Maximum weight of a bag attached to the adjustable handle is 3 kg.
 The maximum load carried in the cup holder must never exceed 1 kg.
 Any additional load suspended from the buggy handles, backrest and sides will cause stability loss.
 Use only parts and accessories supplied or recommended by the manufacturer. Do not use other parts or accessories.
 Lift the front suspension when going up a curb or step.
 Do not place the product near open flame or other heat sources.
 Do not use with an additional platform.
 Stop using the baby carriage if you have any doubts concerning its usage or suspect any danger.
B. ASSEMBLY
I. BUGGY COMPONENTS
A. Frame
B. Fron wheels x2
C. Rear wheels x2
II. . UNFOLDING THE FRAME OF THE BABY STROLLER
Place the frame (A) on a flat surface. Start unfolding the Baby stroller by pressing the parents' handle against the Baby
stroller frame so that all the elements are tightly connected (Fig. 1, A), then move the button on the parents' handle (I) and
press the big button (II) as shown in Fig. 1, B. Pull the baby stroller frame upwards until it locks.
III. WHEELS MOUNTING AND DISMOUNTING
To mount the rear wheels (C), slide them into the holes in the frame until you hear a characteristic click (Fig. 2 A). Slide the
front wheels (B) into the holes in the front of the frame until they lock (Fig. 3 A).
The rear wheels are removed by pulling the metal buckle under the baby stroller frame (Fig. 2, B), while the front wheels
can be removed by pressing the button on the front of the frame (Fig. 3, B). The front wheels can be locked for straight
ahead driving. This function is activated by moving the slider as shown in Fig. 3 C. To unlock the front wheels, move the
slider to its initial position
NOTE! Before using the buggy, make sure that all the wheels are
properly installed.
IV. SEAT MOUNTING AND DISMOUNTING
ATTENTION! There are gray stripes on the sides of the seat to help with the correct installation of this element.
The first step is to position the backrest properly against the seat. To do this, lift the lever on top of the backrest and adjust
the backrest to the seat so that the grey stripes form a single line, then slide the seat (E) onto the Baby stroller frame (Fig.
4). The seat can be mounted both backwards and forwards to the parent.
To remove the seat, lift the backrest upright (using the mentioned lever) until the grey lines are aligned (as shown in Fig. 4)
and pull the seat out.
V. ASSEMBLY/DISASSEMBLY OF THE SAFETY BAR AND FOOTREST COVER, CANOPY ADJUSTMENT
The safety bar (D) is mounted by pushing it into the seat frame as shown in figure 5. Once it is mounted correctly, you will
hear a click. To remove the safety bar, press the buttons in the bar and pull it out.
Push the footrest cover (G) over the stroller and fasten it with clips.
Mounting and adjusting the canopy - to mount the canopy (F), slide it into the frame as shown in figure 6 and then attach
the back of the canopy to the tension and Velcro fasteners on the back of the backrest. The canopy can be adjusted in
several positions. It is disassembled by pressing the buttons, sliding the canopy out and releasing the tension and Velcro on
the back of the backrest (Fig. 6).
VI. USING THE BRAKE
The baby stroller is equipped with a foot brake on the rear axle (Fig. 7). Press the pedal to activate the brake. Lift the pedal
upwards to unlock the brake.
VII. ADJUSTMENT OF THE BACKREST, FOOTREST, MOUNTING OF THE CUP HOLDER.
It is possible to adjust the stroller backrest in 3 positions (Fig. 8A). To do this, pull the lever on top of the backrest and place
it in a comfortable position for the child. The backrest locks automatically.
The footrest can be adjusted in one of 4 positions (Fig. 8B). Press the buttons on both sides of the footrest at the same time
and adjust to the desired position. To adjust the parent handle, press the lock buttons on both sides of the buggy and adjust
the handle to a comfortable height (Fig. 8B)
To mount the cup holder (I), slide it over the protruding pin in the frame (Fig. 9).
VIII. INSTALLATION OF THE MOSQUITO NET AND RAIN COVER
Put the mosquito net on the seat and secure it with the straps at the back of the seat (Fig.10)
Put the rain cover on the seat and secure it with the straps on the sides of the seat. Attention! Before fastening the rain
cover make sure to remove the lower clips of the footrest cover
D. Armrest
E. Seat with safety belts
F. Canopy
G. Footrest cover
H. Rain cover
I. Cup holder
17
J. Mosquito net