Download
Share
Print this page
Glasdon MODUS 770 Operational, Assembly & Fixing Instruction Leaflet
  1. Manuals
  2. Brands
  3. Glasdon Manuals
  4. Outdoor Furnishing
  5. MODUS 770
  6. Operational, assembly & fixing instruction leaflet

Glasdon MODUS 770 Operational, Assembly & Fixing Instruction Leaflet

Flat pack
Hide thumbs Also See for MODUS 770:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
MODUS 770 AND MODUS 1280 (FLAT PACK)
OPERATIONAL, ASSEMBLY & FIXING INSTRUCTION LEAFLET
NOTE: Ensure that all relevant personnel read the points listed below and that a copy is passed on to staff involved
with the installation. Please also refer to the 'Manual Handling Operations Regulations 1992' during the
handling of the product and materials used for installation. The total weight of this product is 102kg
(Modus 770) and 119kg (Modus 1280).
OPENING AND CLOSING HOUSING:
1
Insert Glasdon Key into lock and
turn anticlockwise to unlock the
door. (Alternatively: Turn twist
lock anticlockwise to unlock
door.)
4
Remove wheeled bin from
housing.
NOTE: To allow the wheeled bin to sit inside the housing in the correct position, it is recommended that
the lid of the wheeled bin remains attached and is simply folded over the back of the bin when in use.
For best results please ensure that the front of the wheeled bin is level with the front two extrusions.
We recommend that a risk assessment is undertaken to identify an appropriate location for your waste
collection and recycling units. In order to reduce risk, some organisations decide to place the units a
minimum of 5 metres away from buildings. Any potential risk can be further reduced by maintaining a
regime of regularly emptying the unit. You may also wish to consider installing a Glasdon Firesafe
Glasdon Firesafe is an e ective low cost auxiliary device designed to quickly extinguish re at source but is
not intended to replace primary re prevention measures. A regular inspection and maintenance
programme will ensure the device is kept in good working order. In the event that the device has been
discharged it must be replaced.
TM
2
Using handle pull door open
to 90 degree position.
5
After replacing the wheeled bin,
remove the door stay catch by
pushing upwards anticlockwise so
that it is positioned vertically.
P. 1
TM
3
To ensure that the door remains
open whilst removing the wheeled
bin, turn the door stay catch
clockwise so that it is positioned
horizontally.
6
Close the door and insert key into
lock. Turn key clockwise to lock
door. (Alternatively: Turn twist lock
clockwise to lock door.)
.
TM

Advertisement

loading
Need help?

Need help?

Do you have a question about the MODUS 770 and is the answer not in the manual?

Questions and answers

Related Manuals for Glasdon MODUS 770

Summary of Contents for Glasdon MODUS 770

  • Page 1 You may also wish to consider installing a Glasdon Firesafe Glasdon Firesafe is an e ective low cost auxiliary device designed to quickly extinguish re at source but is not intended to replace primary re prevention measures. A regular inspection and maintenance programme will ensure the device is kept in good working order.
  • Page 2 Nylon Washer 10.3 x 20.6 x 3.2mm ITEM O 4.8 x 60mm Screw S/S ITEM P Repair Washer M5 x 25mm S/S ITEM Q M6 x 25mm A2 Socket Cap Screw ITEM R M10 x 120mm Ground Fixing Bolt ITEM S Glasdon Key P. 2...
  • Page 3 Step 1: Assembly of Housing Using rubber mallet (so not to Hold panel (B) up to the extrusion Tap the top of the extrusion to damage the extrusions) tap the on panel (A) ensuring that the ensure the board is level up to the side at the top of the extrusion so feet with the pre-drilled holes are top of the extrusion.
  • Page 4 Step 1: Assembly of Housing (continued) Using hand drill and screw Using rubber mallet, tap the side Using hand drill and 6 o screws provided (K), secure the top xing at the bottom of the extrusion to provided (K), secure the in position by screwing from the ensure that the board is pushed remaining xings on the inside of...
  • Page 5 Step 1: Assembly of Housing (continued) To test the lock, Insert Key Now that all the panels are Ensure that there is one nut in assembled, lift the hood (may require each of the moulded legs. If not, into triangular lock and turn two people to lift) and locate the place one nut into each...
  • Page 6 Step 1: Assembly of Housing (continued) Close the door. Should the gap Open door and using 9 o screws To put the nal xings on the between the door and the (K) and hand drill, x through the hood, on the inside at the top of extrusion be too small (as above) extrusion pre-drilled holes into the 4 o extrusions, x 2 o...
  • Page 7 Step 2: Adjustment of Spigot Legs When Sited on Uneven Ground (If not required move on to Step 3) Using a 13mm spanner/socket Lift the extrusion upwards and Replace the bolts and washers unscrew the two bolts with pull the spigot leg down to a into the new holes within the washers on the inside at the more appropriate height ensuring...
  • Page 8 Step 4: Adjustment of Door Wheel (If Required) IMPORTANT NOTE: The door wheel must be positioned so that it is touching the ground when the door is CLOSED. The main purpose of the door wheel is to support the large door when in the closed position. If the door is not level and there is Using 17mm spanner, loosen Using 17mm spanner and 6mm...
  • Page 9 Replacement components are available direct from GLASDON. Glasdon U.K. Ltd reserves the right to alter specifications without prior notice. BLACKPOOL GLASDON cannot be held responsible for claims arising from incorrect installation, unauthorised modifications or misuse of Lancashire FY4 4UL the product.

This manual is also suitable for:

Modus 1280