Glasdon MODUS 770 Flat Pack Assembly & Fixing Instruction Leaflet
Smoking shelter
Hide thumbs
Also See for MODUS 770:
Advertisement
Quick Links
FLAT PACK
NOTE: Ensure that all relevant personnel read the points listed below and that a copy is passed on to staff involved
with the installation. Please also refer to the 'Manual Handling Operations Regulations 1992' during the
handling of the product and materials used for installation.
CONTENTS:
Smoking Shelter Optional Extras
Standard Shelter Optional Extras
Section 5 : ADJUSTMENT OF LEGS
MODUS SHELTER 770 AND 1280
TM
ASSEMBLY & FIXING INSTRUCTION LEAFLET
Page 1
Page 1-2
Page 3
Page 4-5
Page 6
Page 7-10
Page 10-15
Page 16
Page 16-17
Page 18
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Glasdon MODUS 770
Summary of Contents for Glasdon MODUS 770
-
Page 1: Table Of Contents
MODUS SHELTER 770 AND 1280 FLAT PACK ASSEMBLY & FIXING INSTRUCTION LEAFLET NOTE: Ensure that all relevant personnel read the points listed below and that a copy is passed on to staff involved with the installation. Please also refer to the ‘Manual Handling Operations Regulations 1992’ during the handling of the product and materials used for installation. -
Page 2: Tools Required
Heavy-Duty Electric Drill Flat Head Screwdriver Scalpel or other sharp blade Pencil and Tape Measure SMOKING SHELTER Assembled Shelter (770) KIT CONTENTS: Modus 770 1280 ITEM 1 770 Roof ITEM 2 1280 Roof ITEM 3 Front Left Corner Extrusion ITEM 4... -
Page 3: Smoking Shelter
SMOKING SHELTER 770 SIZE 1280 SIZE P. 2... - Page 4 SMOKING SHELTER OPTIONAL EXTRAS: (please refer to your order) Full Rear Ecoboard Panel Kit Modus 770 1280 ITEM 33 Pozi Pan Screw 60mm ITEM 34 Washer M5 x 25mm OD ITEM 35 Ecoboard Panel Rear Top As well as the above additions, the following item QTY’s are affected:...
-
Page 5: Standard Shelter
STANDARD SHELTER Assembled Shelter (770) KIT CONTENTS: Modus 770 1280 ITEM 1 770 Roof ITEM 2 1280 Roof ITEM 3 Front Left Corner Extrusion ITEM 4 Front Right Corner Extrusion ITEM 5 Rear Corner Extrusion ITEM 6 Spigot Leg ITEM 7... - Page 6 STANDARD SHELTER 770 SIZE 1280 SIZE P. 5...
- Page 7 STANDARD SHELTER OPTIONAL EXTRAS: Please refer to your order Full Rear Ecoboard Panel Kit Modus 770 1280 ITEM 33 Pozi Pan Screw 60mm ITEM 34 Washer M5 x 25mm OD ITEM 35 Ecoboard Panel Rear Top As well as the above additions, the following item QTY’s are affected:...
-
Page 8: Section 1: Assembly Of Shelter
Section 1: Assembly of Shelter 23 24 745mm Slide all 4 Spigot Legs (ITEM 6’s) Measure from the top of the Take the Rear Panel (22) and slide into the bottom of each of the Extrusion and mark in pencil a it into the right hand slot in one of Corner Extrusions (3-5). - Page 9 Peel back (but do not remove) this Slide the 3 x PETG Panels (12 and Push the Middle Support Exrusion outer sheet from all the edges. 10 or 11) into the slots in the (15) onto the top edge of the Insert the Panel Clamp (16) into the Corner Extrusions from the top.
- Page 10 28 29 Use the M10 Fixings (28-29) to Lift the Roof (1 or 2) above the Slide the Roof Corner Brackets (26) secure the Roof to the Corner shelter and drop the Roof legs into the largest cavity in the Front Extrusion through the central hole, into the Extrusions (3-5) in the Corner Extrusions with the part of the...
-
Page 11: Section 2: Assembly Of Shelter - Optional Extras
Section 2: Assembly of Shelter - OPTIONAL EXTRAS Move straight onto SECTION 3 if your shelter does not include any of these features: 1. FULL REAR BACK PANEL SEE STEPS 26-29 2. PERCH SEAT 1200 SEE STEPS 30-37 3. PERCH SEAT(S) 600 SEE STEPS 38-39 4. - Page 12 2. PERCH SEAT 1200 Hold the Seat (41) where you want From inside the shelter, drill the From outside the shelter fit one of it to be positioned on the Rear upper left fixing keyhole through the Coach Bolts (42) through the Panel (ensure the top of the Seat is the Panel using a 12mm drill bit drilled hole.
- Page 13 3. PERCH SEAT 600 For the Perch Seat 600 these are The seat can be placed centrally or fitted on the interior Side Panels to either side of the the Side (see above). The installation is very Panels. However, please ensure the similar to the Perch Seat 1200 so top of the seat is installed at a follow the same procedures as...
- Page 14 4. ASHMOUNT SG LIFT OFF MOUNTING Open the unit and line up the Drill four pilot holes using a 3mm Open the Ashmount SG and bulbous ends of the ‘L’ shaped slots drill bit (CAUTION - DO NOT DRILL remove the liner. Pop out the four with the screw heads sticking out ALL THE WAY THROUGH THE ‘L’...
- Page 15 6. BLANK SIGNAGE PANEL ADDITIONAL TOOLS REQUIRED: 3mm Drill Bit Position the Signage Panel (45) in Ensure the Panel is correctly From inside the shelter, drill the the sign recess in the Roof at the positioned. Looking from the Signage Panel through the two front of the shelter.
- Page 16 7. POLYCARBONATE SIGNAGE Position the Polycarbonate Using a 3mm drill bit drill three Fix the Panel through the three Signage Panel (49) in to the small pilot holes through the fixing holes drilled with the hand desired position on the Blank three holes shown above.
-
Page 17: Section 3 : Unpacking The Shelter
Section 3: Unpacking the Shelter (when supplied pre-assembled) Position the shelter close to the intended site using a pallet truck or forklift. Unfasten the screws holding the shelter to the pallet using the hand drill with pozi drill bit attached. PLEASE NOTE: A pre-laid concrete foundation should be prepared prior to installation. - Page 18 CONCRETE BASE - RECOMMENDED MINIMUM DIMENSIONS. !!IMPORTANT!! MODUS SHELTER 770 1900 1200 MODUS SHELTER 1280 1900 1550 P. 17...
- Page 19 Section 5: Adjustment of Spigot Legs when sited on uneven ground Using a 13mm spanner/socket Lift the Extrusion upwards and Replace the Bolts and Washers unscrew the two Bolts (23) with pull the Spigot Leg down to a into the new holes within the Washers on the inside at the more appropriate height ensuring Spigot Leg and tighten with a...
- Page 20 (01253) 600410 Replacement components a re available di rect from GLASDON. Fax: (01253) 792558 GLASDON cannot be held responsible f or claims arising from incor rect insta llation, unautho rised modifications or mi suse of e-mail: sales@glasdon-uk.co.uk the p roduct.
Need help?
Do you have a question about the MODUS 770 and is the answer not in the manual?
Questions and answers