Directions For Use; Tips To Ensure A Better Milk Flow; Operating The Device; Two-Sided Pumping - Microlife BC 300 Maxi 2 in 1 Manual

stances should you hold the motor unit under water, as this can
cause liquid to enter and damage the device.

Remove batteries if the device is not going to be used for a
prolonged period.

4. Directions for Use

Tips to ensure a better milk flow
 Choose a time and location to use the device where you can
relax.
 Having your child nearby or looking at a picture of your child can
have a positive effect on the milk flow.
 If feeding your child using one breast, use the device on the
other breast at the same time.
 Warmth and relaxation encourage milk flow. Use the device
after having a shower or bath.
 If your breasts are swollen or sore, place a warm towel on them
for a few minutes. This will improve the milk flow.
 If the milk does not start to flow from your breasts immediately,
try to relax and then try again a few minutes later.
 If the device still does not extract any milk from your breasts
after five minutes, stop using it and try again later.
 If you experience any sharp pains when using the device,
consult a doctor.

Operating the device

Two-sided pumping

1. Before using the device, wash your hands and breasts thoroughly.
2. The device 1 and the 2 bottles AL must be connected to the
silicone tube for two-sided pumping.
3. Sit with your upper body lent forwards slightly. You can support
your back better by using a pillow.
4. Place the breast shields with silicone cushion AK gently on the
breast. Make sure that the nipples are completely enclosed and
there are no air pockets. To ensure proper function, the breast
shields must be drawn firmly onto the breasts.
5. Press the ON/OFF button 3 to switch on the device.
6. After switching on the device for the first time, the software will
be in dual pump mode and the display will show mode «2» BK.
This mode should always be selected for two-sided pumping. In
case the software starts in mode «1» (one-sided pumping),
press + 5 and – 6 simultaneously for 3 seconds to switch to
mode «2».
6
7. The device will begin automatically in stimulation mode BM and
a two-minute timer BN will appear on the display. During these
two minutes, your breast nipple will be stimulated in order to
prepare it for pumping the breast milk. Use the + / – buttons 5
6 to set the desired stimulation intensity.
8. After the two minutes have passed, the timer will start to flash
on the display. Press the MODE button 4 to begin pumping the
breast milk. Use the + / – buttons to select a suction intensity
that is comfortable for you. When the milk reaches 180 ml inside
the feeding bottle, interrupt the suction.
9. If you want to switch back to the stimulation mode, press the
MODE button 4. The stimulation and the two-minute timer will
start from the beginning.
10.Press the ON/OFF button 3 to switch off the device.

NOTE:
This device includes a memory function, which recalls the
last programmed stimulation or pumping level when it is
switched on.

NOTE:
The one-sided pump mode «1» or dual pump mode «2» will
also be stored. For dual pump mode «2», the silicone tube
for two-sided pumping must be connected to the device.

This device was designed for intermittent use of 30
min. On / 30 min. Off. Switch off the device after 30 min.
use and wait for another 30 min. before you resume.

NOTE:
This device is also suitable for one-sided pumping. Please
refer to the following section «One-sided pumping» for
detailed instructions.

One-sided pumping

1. Before using the device, wash your hands and breasts thoroughly.
2. For one-sided pumping, insert the silicone tube for one-sided
pumping into the device 1 and the pump attachment AT.
3. Sit with your upper body lent forwards slightly. You can support
your back better by using a pillow.
4. Then place the breast shield with silicone cushion AK gently on
the breast. Make sure that the nipple is completely enclosed
and there are no air pockets. To ensure proper function, the
breast shield must be drawn firmly onto the breast.
5. Press the ON/OFF button 3 to switch on the device.