Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Maytronics Dolphin Liberty
Summary of Contents for Maytronics Dolphin Liberty
- Page 1 Dolphin Liberty User Instructions 8151190...
-
Page 3: Table Of Contents
Dolphin Liberty User Instructions Contents 1. INTRODUCTION ..............2 2. WARNINGS AND CAUTIONS..........2 3. SPECIFICATIONS ..............3 3.1. Robot specifiactions ............3 3.2. Charger specifications ............3 3.3. Battery specifications ............3 4. WHAT YOU’LL FIND INSIDE THE BOX ........4 5. -
Page 4: Introduction
Please read this instruction manual carefully and be sure to follow all the recommendations regarding operation and care of your Dolphin Liberty. This is essential for optimal cleaning and to protect your robot at all time, whether in use or in storage. -
Page 5: Specifications
• Storage Temperature: 0°-30°C / 32°-86°F • Safety Device: Each cell is equipped with a safety vent system. Each pack is equipped with a protection circuit against over-voltage, over-discharge and over-current. • Safety Regulation: UL1642, (UL file no.: MH21015), UN38.3 Dolphin Liberty User Instructions... -
Page 6: What You'll Find Inside The Box
Brushes - options Cartridge with Spring net filter ultra-fine filters Combined brush For rough ceramic surfaces and mosiac tiles. Charging cable PVC brush Wonder brush For concrete, PVC, For smooth ceramics. Pulling hook fiberglass and liner. Dolphin Liberty User Instructions... -
Page 7: Using The Pool Cleaner
Master 4 D02B To adjust the handle angle: A. Press the latch down and hold it in position. B. Move the handle to the desired position and release the latch to hold the handle in place. Dolphin Liberty User Instructions... - Page 8 Charging cable Charging Cable connector to Cahrger 1. Plug the charging cable into the charger. 2. Plug the electrical cable from the charger into the mains. 3. Open the charging connector cover of the charging cable. Dolphin Liberty User Instructions...
-
Page 9: The Interactive Float
Open the charging socket cover on the float. Connect the charging connector to the charging socket on the float (1) with a slight rotation until in position, push down and turn to secure in place (2). Dolphin Liberty User Instructions... -
Page 10: Placing The Robot In The Water
1. Before operation, disconnect the charging cable from the float and close the charging socket cover. 2. Put the robot into the water while holding the float. Let the robot descend to the bottom of the pool. Dolphin Liberty User Instructions... -
Page 11: Taking The Robot Out Of The Water
Upon completion of an operating cycle, the robot automatically switches off and moves to one of the pool walls to make pulling it out of the pool easier. Bring the robot to the surface by gently pulling the float and cable. Dolphin Liberty User Instructions... - Page 12 Pull the floating cable gently until the robot has risen to the surface. Lift the robot out of the water by its handle. Important: Do NOT lift the Dolphin from the water by its cable. CAUTION Dolphin Liberty User Instructions...
-
Page 13: Routine Maintenance
Note: Do not let the filter cartridges dry out before cleaning. CAUTION 1. Open the filter covers and remove the cartridges from both sides of the robot. 2. Open the clips and remove the filters. 3. Clean the filters with a hose. Dolphin Liberty User Instructions... -
Page 14: Dismantling And Cleaning The Impeller
CAUTION the on/off switch on the float. The LEDs will blink for several seconds before shutting down. If you notice debris trapped in the impeller, open the impeller and remove the debris, then reassemble. Dolphin Liberty User Instructions... -
Page 15: Storing The Robot
• Do NOT store the robot where it will be exposed to direct sunlight. • Do NOT store the robot where it will be exposed to excessive heat. • Do NOT store the robot where it will be exposed to frost. Dolphin Liberty User Instructions... -
Page 16: Using The Remote Control
When flashing, change the batteries Manual control indicator When flashing, you are in manual direction control mode Cleaning cycle icons Delay timer icons Cleaning mode icons ON/OFF button Manual/automatic select button Set/OK button Direction control arrows Dolphin Liberty User Instructions... -
Page 17: Manual Direction Control Mode
1. To change the parameters press the up or down arrows. To select the parameter settings use the right or left arrows. 2. When you reach the required function press the Set/OK button. Dolphin Liberty User Instructions... -
Page 18: Automatic Mode Settings
The robot will continue to work according to the last settings chosen. • After “Ultra-clean” and “Walls only” cleaning cycles, the robot returns to default settings. • In “Floor only” mode, the cleaning cycle will stay as it is until deliberately changed. Dolphin Liberty User Instructions... -
Page 19: Troubleshooting Guide
When the on button on the float is The battery is empty. Recharge the battery. pressed the robot does not begin to work and the red LED flashes. Dolphin Liberty User Instructions... -
Page 20: Caddy Assembly Instructions
11. CADDY ASSEMBLY INSTRUCTIONS Dolphin Liberty User Instructions... - Page 21 8mm ( ”) Dolphin Liberty User Instructions...
- Page 24 Dolphin Liberty www.maytronics.com...
Need help?
Do you have a question about the Dolphin Liberty and is the answer not in the manual?
Questions and answers