Advertisement
...............................................................................................................................
Installation steps
1.
Insert a screwdriver into the keyslot , and open the end lids.
2.
Unscrew and remove the cable retainers on both sides of the controller box
3.
Insert RJ12 DyNet connectors into sockets.
4.
Fasten the cable clamp on the cable of the DyNet cable(s).
5.
Remove at least 10 mm of insulation and fasten load power cables into pressure-pad screw terminals , CH1, CH2
6.
Remove at least 10mm of insulation and fasten L and N mains cables into pressure pad screw terminals.
7.
Fasten the cable clamp over the power leads.
8.
Close end lids on both sides after terminations are complete.
9.
Fix the housing to a fixed flat surface using two screw flanges and 5 mm screws. Allow no contact with other devices.
10. For indoor use only. Observe IP rating requirements in installation.
11. DIPswitches are set according to Truth Tables; see Channel 1 and Channel 2 tables.
.......................................................................................................................................
..
Mounting dimensions
Recommended Cable
200m Unterminated Roll: DYNET-SFLAT6-CABLE
10m Patchlead: DYNET-SFLAT6-CABLE-10M
5m Patchlead: DYNET-SFLAT6-CABLE-5M
3m Patchlead: DYNET-SFLAT6-CABLE-3M
Reference:
Philips Dynalite EcoSet System Technical Guide
...............................................................................................................................
Product specifications
Supply
100-240V 50/60Hz Single Phase at 20A
Dynet DC Supply:
150mA@12VDC
Switched output
2 x switched output at 10A (inductive)
Switching Device
Relay, Tungsten Carbide pilot contact,
12A inductive, 120A surge
Control Inputs
1 x RS485 DyNet/2 X RJ12 connectors
File button configurations R7
Web: dynalite-online.com
E-Mail: info@ dynalite-online.com
Tel: 161-2 8336 9899
DMRC210-RJ-DA Installation Instructions Rev A Sept 2010
Specifications subject to change without notice. All rights reserved.
Dynalite, DyNet and associated logos are the registered trademarks
of Philips Dynalite. Not to be reproduced without permission.
Manufactured by WMGD Pty Ltd (ABN 33 097 246 921) Unit 6, 691
Gardeners Road, Mascot, NSW 2020, Australia
...............................................................................................................................
Channel 1
Area
Sw1
Sw2
Sw3
Sw4
1.
ON
0
0
0
0
ON
0
0
2.
ON
ON
0
0
3.
4.
0
0
ON
0
ON
0
ON
0
5.
6.
0
ON
ON
0
ON
ON
ON
0
7.
8.
0
0
0
ON
ON
0
0
ON
9.
10.
0
ON
0
ON
ON
ON
0
ON
11.
0
0
ON
ON
12.
13.
ON
0
ON
ON
14.
0
ON
ON
ON
ON
ON
ON
ON
15.
0
0
0
0
16.
17.
ON
0
0
0
0
ON
0
0
18.
19.
ON
ON
0
0
0
0
ON
0
20.
21.
ON
0
ON
0
0
ON
ON
0
22.
23.
ON
ON
ON
0
0
0
0
ON
24.
ON
0
0
ON
25.
26.
0
ON
0
ON
ON
ON
0
ON
27.
28.
0
0
ON
ON
ON
0
ON
ON
29.
30.
0
ON
ON
ON
ON
ON
ON
ON
31.
Supply Terminals
Line, Neutral
1 x 4mm2 max conductor size
Output Terminals
CH1, CH2, Neutral
1 x 4mm2 max conductor size
Compliance
CE, C-Tick
Operating Environment
0º to 50ºC ambient temp
0% to 90% RH non condensing
IP rating
: 20 (all supplied lids closed)
Enclosure
polycarbonate
Dimensions
L 240mm x W 45mm x D 38mm
Weight
Packed weight 0.19kg
Channel 2
Sw5
Area
Sw6
Sw7
0
1.
ON
0
0
0
ON
2.
0
ON
ON
3.
0
4.
0
0
0
ON
0
5.
0
6.
0
ON
0
ON
ON
7.
0
8.
0
0
0
ON
0
9.
0
10.
0
ON
0
ON
ON
11.
0
0
0
12.
0
13.
ON
0
0
14.
0
ON
0
ON
ON
15.
ON
0
0
16.
ON
17.
ON
0
ON
0
ON
18.
ON
19.
ON
ON
ON
0
0
20.
ON
21.
ON
0
ON
0
ON
22.
ON
23.
ON
ON
ON
0
0
24.
ON
ON
0
25.
ON
26.
0
ON
ON
ON
ON
27.
ON
28.
0
0
ON
ON
0
29.
ON
30.
0
ON
ON
ON
ON
31.
Sw8
Sw9
Sw10
0
0
0
0
0
0
0
0
0
ON
0
0
ON
0
0
ON
0
0
ON
0
0
0
ON
0
0
ON
0
0
ON
0
0
ON
0
ON
ON
0
ON
ON
0
ON
ON
0
ON
ON
0
0
0
ON
0
0
ON
0
0
ON
0
0
ON
ON
0
ON
ON
0
ON
ON
0
ON
ON
0
ON
0
ON
ON
0
ON
ON
0
ON
ON
0
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Advertisement
