Tascam HS-4000 Release Notes page 7

•
When using an external keyboard, if Caps Lock was
enabled, Function key operations could not be used.
This has been fixed.
•
If a file had been overwritten via FTP, a playback error
would occur. This has been fixed.
•
On the ANALOG Ref. LEVEL ADJUST screen, when the
numeric input level is showing -18.0dB or -9.0dB, the
meter bar also now reaches the -18dB/-9dB Ref Level
line.
•
When a data reading error occurs now, the unit stops
and an error message appears only after all the read
audio data is output.
•
The unit did not respond to drop frame flags in
the timecode of time data returned via the RS–422
connector. This has been fixed.
•
When the Pause Mode was set to NO SPLIT, when
recording was restarted from a paused state, recording
for the full duration of remaining recordable time was
not possible. This has been fixed.
•
When the Pause Mode was set to SPLIT, in timeline
mode if recording was paused and then stopped,
timeline data would not be saved. This has been fixed.
•
When a mark was set on the
screen, the mark icon would not be shown. This has
been fixed.
•
After copying a file, the remaining space on the copy
destination medium was not updated. This has been
fixed.
•
When started while connected to a RC-HS32PD, this
unit's touch panel did not function in some cases. This
has been fixed.
•
When loading a project created using an HS-P82 or HS-
8, the rec arms could not be set in some cases. This has
been fixed.
•
If started in on-air mode when no CF card was loaded,
the displayed sampling frequency value was not the
one for on-air mode, but rather the value of the last
loaded project, and loading a CF card would cause the
sampling frequency shown to change. This has been
fixed.
•
When copying a take, sometimes copying would not
be possible because the unit mistakenly determined
that the copy destination lacked sufficient space or that
it contained a file with the same name. This has been
fixed.
•
When copying a session, if the copy destination already
contained a session with the same name, that session
would be overwritten by the copy without warning.
This has been fixed to allow you to confirm that you
want to override an existing file.
•
In on-air mode, after adding multiple takes via FTP,
switching with the ON AIR button did not work
properly, and the time display would not be updated
even during playback. This has been fixed.
•
If the playback duration registered in a playlist is
longer than the actual length of the file, it will now be
adjusted to the actual length.
HS-4000
Playlist Adjust
Release Notes
•
Setting marks in files that were not created by this unit
would not always work properly. This has been fixed.
•
After importing an AES31 file, the timecode frame type
shown on the screen and output were different. This
has been fixed.
•
In on-air mode, changing various settings caused the
time display mode to change. This has been fixed.
•
Even if the Frame Type item on the
screen was changed, the value shown for
SYNC T/C
the on the project information pop-up
Frame Type
on the project screen was not changed in some cases.
This has been fixed.
•
In timeline mode, when
Pause Mode
after pausing recording, the position where recording
restarts has now been changed so that it is the same
position as when recording is restarted after recording
has been stopped.
•
JAM SYNC did not synchronize in some cases. This has
been fixed.
•
In timeline mode, if BC$FILE and BC$PAUSE marks were
set in that order, both Pause and Standby tallies would
be output at the BC$PAUSE mark. This has been fixed.
•
In timeline mode, if you turned Chase OFF during
Chase playback, playback would restart from the
beginning of the timeline. This has been changed so
that now playback continues from the position where
Chase was turned OFF.
•
In playlist mode, if the e button was pressed to load
a session to put into standby (when Follow BWF-J was
ON and the first take had a BC$STANDBY mark), files
did not appear on the Playlist selection screen. This has
been fixed.
•
Depending on the file name, the file name shown on
RC-HS32PD flash keys might be cut off. This has been
fixed.
•
In timeline mode, after starting playback from a
little before 24:00 ABS time, if you started punch-in
recording, an error would cause recording to stop and
recording data to be lost. This has been fixed.
•
In take mode, after pausing recording, an auto mark
would not be added when recording was restarted.
This has been fixed.
•
When the time display mode is T/C, in modes other
than timeline, entering locate times greater than 24:00
is now possible.
•
Since files that are 2 GB or larger can only be played
back until the 2GB point, the unit no longer recognizes
files that are 2 GB or larger as takes.
•
On some USB keyboards, inputting the "}" character
was not possible. This has been fixed.
•
In on-air mode, WAV files with sampling frequencies
that matched the on-air sampling frequency ceased to
be shown in the list in some cases. This has been fixed.
•
In playlist mode, if another entry was flash started just
before the end of the last entry, the flash started entry
would end suddenly and playback of the next entry
would start. This has been fixed.
page of the
SETUP
is set to ,
SPLIT
7
TASCAM HS-4000