Public use wheelchair lifts, solid platform (48 pages)
Summary of Contents for BraunAbility GA Series
Page 1
Failure to do so may result in serious bodily 401338 injury and/or Rev. B property damage. 631 West 11th Street, P.O. Box 310, Winamac, IN 46996, USA August Phone: 1-574-946-4139 • 1-800-THE-LIFT • www.braunability.com 2015...
Page 2
ADDRESS CITY the cards. The consumer must fill out the other TELEPHONE STATE card and mail it to BraunAbility . The warranty is TO VALIDATE WARRANTY ® REGISTRATION CARDS MUST BE RETURNED TO THE BRAUN CORPORATION. provided in this manual. The warranty cards must Sample Warranty/Registration Card be processed to activate the warranty.
5. Remove the threshold warning plate and replace non-functioning threshold switch. 6. Repeat Step 4. If warning is still not activated, call BraunAbility Aftersales. • Platform movement is prohibited beyond the position where the inner roll stop is fully deployed (up).
Platform Fold Pressure Adjustment 1. Position the platform at the floor level loading position. 2. Loosen the hex nut on the adjustment screw (do not remove hex nut). 3. Turn the adjustment screw counter clockwise until the platform does not fold when the Fold button is pressed.
Platform Angle Adjustment Lowering Sequence Requirements Figure A 1. The outboard end (toe) of the platform must contact the ground first to ensure the spring-loaded outer barrier unfolds fully. See Figure A. Barrier 2. The inboard end (heel) of Heel the platform must lower fully (vertical arms must contact Ground Level...
Platform Angle Adjustment Adjustment Allen screws are To raise the outboard end of Note: Both adjustment screws provided on each side of the lift platform - turn adjustment must be adjusted equally. screw clockwise. platform for adjusting the platform angle. Adjust platform angle as To lower the outboard end specified on previous page.
Outer Barrier Switch Lever Activation Foot Pivot Points (2) Bearings (4) See the Maintenance/Lubrication Schedule for recommended applications per number of cycles. Specified (recommended) Available BraunAbility Lubricant Type Lubricant Amount Part No. Light Penetrating Oil LPS2, General Purpose 16 oz.
4500 cycle maintenance serious bodily injury procedures. These BraunAbility dual parallel arm lifts are equipped with and/or property hardened pins and self-lubricating bushings to de- intervals are a general damage.
Page 14
Maintenance and Lubrication Schedule continued Correct or replace damaged parts. Inspect outer barrier for proper operation Correct or replace damaged parts and/or relubri- Inspect outer barrier latch for proper operation, cate. See Lubrication Diagram positive securement, and detached or missing spring(s) See Platform Fold Pressure Adjustment Adjust fold pressure...
Page 15
Maintenance and Lubrication Schedule continued Inspect inner roll stop locks (2) and torsion springs Replace damaged parts. Apply Light Oil to inner (2) for wear or damage and for proper operation roll stop lock pivot point. Inspect external snap rings: Resecure or replace if needed.
Page 16
Maintenance and Lubrication Schedule continued Resecure or replace if needed. Inspect vertical arm plastic covers Resecure, repair or replace if needed. Inspect power cable 4500 Check to see that the lift is securely anchored to Mounting Cycles the vehicle and there are no loose bolts, broken welds, or stress fractures.
✓ Seal Kits: If repairing a cylinder, order Seal Kit #1500-0500P. “Down” Valve “Dual Relief” Valve * Raw material items ordered and priced per inch (order specified length). (complete) (complete) Coil Coil #400783 Hydraulic Fluid #400783 When adding or chang- ing hydraulic fluid, use BraunAbility 32840-QT (Exxon Univis HVI 26) ® hydraulic fluid (do not mix with Dextron III or other Cartridge Cartridge #31121 #26078 hydraulic fluids). Page 18...
Hydraulics Diagram Hydraulic Repair For repair of a hydraulic hose or cylinder, read this. Hydraulic Service Bulletin 27049 Pump Motor Manual Backup Pump Page 19...
Pump Module Diagram Pump Mounting Bolts Apply Loctite Threadlocker Red 271™ ® or equivalant to the three pump mount- ing bolts (items 25 and 26) if a blue nylon patch is not present on the bolts when retrofitting an M268 pump as- sembly. Note: Rear pump module shown, front pump module mirror image.
Exploded Views and Parts Lists NCL954IB3454-2 Base Plate Assembly DWG. NOTES 1) LOOP TAPESWITCH WIRE BACK AND SECURE WITH WIRE TIE 4X. 2) TRIM AND TUCK WIRE TIE CLASP INTO HOLE 4X. 3) APPLY LOCTITE THREADLOCKER RED 271™ ® OR EQUIVALANT TO ALL #25527 SCREWS. NOTE: "A"...
Exploded Views and Parts Lists NCL954FIB3454-2 Base Plate Assembly DWG. NOTES 1) LOOP TAPESWITCH WIRE BACK AND SECURE WITH WIRE TIE 4X. 2) TRIM AND TUCK WIRE TIE CLASP INTO HOLE 4X. 3) APPLY LOCTITE THREADLOCKER RED 271™ ® OR EQUIVALANT TO ALL #25527 SCREWS. NOTE: "A"...
Exploded Views and Parts Lists Bottom Parallel Arm Assembly - Rear PART NO. DESCRIPTION ITEM QTY. 18349 NUT-#10-32 W/LOCKWASHER/AUTO-BK 32514NA-54 ASSY-IB OCCUPIED 34398 WASHER-0.906"ID X 1.25"OD X .075"TH/ZINC 24011 BEARING-FLANGE-3/4" X 3/8"-12FDU06 954-0458NA ASSY-ARM-PARALLEL/BOTTOM/PUMP (Incl. Items 1-5) Bottom Parallel Arm Assembly - Front ITEM QTY.
Exploded Views and Parts Lists Vertical Arm Assembly - Front DWG. NOTES 1) INSERT SOCKET OF LIGHT ASSY THRU TOP KEY WHILE INSTALLING LIGHT. TIGHTEN SCREWS. DWG. NOTES 2) APPLY LOCTITE THREADLOCKER BLUE 242 OR EQUIVALENT ® ® 1) INSERT SOCKET OF LIGHT ASSY THRU TOP KEY 3) APPLY LOCTITE THREADLOCKER RED 271™...
Exploded Views and Parts Lists Arm Cover Assembly - Front SMOOTH SIDE SMOOTH SIDE SMOOTH SIDE SMOOTH SIDE ITEM QTY. PART NO. DESCRIPTION 954-0704NA COVER-PLASTIC-PARALLEL ARM-OUTSIDE-FRONT 954-0701NA COVER-PLASTIC-PARALLEL ARM-INSIDE-FRONT ITEM QTY. PART NO. DESCRIPTION 954-0704NA COVER-PLASTIC-PARALLEL ARM-OUTSIDE-FRONT 954-0701NA COVER-PLASTIC-PARALLEL ARM-INSIDE-FRONT Arm Cover Assembly - Rear SMOOTH SIDE SMOOTH SIDE...
Exploded Views and Parts Lists Platform Assembly DWG. NOTES 1) USE LOCTITE THREADLOCKER RED 271™ OR EQUIVALENT ON SCREWS (B.C. #24537, B.C. #15733 & B.C. # 81068-000 ). ® 2) USE LOCTITE THREADLOCKER GREEN 290™ OR EQUIVALENT ON CLEVIS PINS (B.C. #24932BK). ®...
WARRANTY COVERAGE AND WARRANTY COVERAGE TIME PERIODS The BraunAbility (“Braun”) warranty covers certain parts of this wheelchair lift for three (3) years or 10,000 cycles and the cost of labor to repair or replace those parts for one (1) year or 3,000 cycles. If The Braun Corporation receives the warranty registration card within 20 days after the lift is put into service, the war- ranty labor coverage will increase from one (1) year or 3,000 cycles to three (3) years or 10,000 cycles.
Page 34
BraunAbility Limited Warranty ® BRAUN SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES THAT MAY RESULT FROM BREACH OF THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY. THIS EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES SHALL BE INDEPENDENT OF ANY...
Page 35
BraunAbility Limited Warranty ® a dealer prior to delivery to the purchaser. You must inspect the product for this type of damage when you take delivery. If you find any such defect or damage you must notify the selling dealer, or Braun, at the time of delivery to have these items covered by this limited warranty and to have work performed on the items at no cost to you as provided by this limited warranty.
Need help?
Do you have a question about the GA Series and is the answer not in the manual?
Questions and answers