ABB devices Pos : 13 /Busc h-J aeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/U mwel t (--> Fü r alle D okumente <--)/Hinweis e/Hi nweis - U mwelt - ABB El ektr ogeräte @ 19\mod_1323162745839_15.doc x @ 110867 @ @ 1 All packaging materials and devices from ABB bear the markings and test seals for proper disposal.
Page 4
ABB-Welcome Environment ABB products meet the legal requirements, in particular the laws governing e lectronic and electrical devices and the REACH ordinance. (EU-Directive 2002/96/EG WEEE and 2002/95/EG RoHS) (EU-REACH ordinance and law for the implementation of the ordinance (EG) No.1907/2006)
ABB-Welcome Terminal description Terminal description Front overview Fig. 1 Front overview Function Light sensor Infrared LED-a total of 6 Indicated LED-a total 3: ring, call and door open Speaker and microphone integration Round pushbutton *If round pushbutton with ID card reader,see details in chapter 5.3...
ABB-Welcome Terminal description Terminal description Fig. 2 Terminal description Functions Connector for device software update Rotary switch to set the address of outdoor station (1-9) Set feedback tone of pushbutton ON/OFF Set general call to all indoor stations in one family GC=ON, press button1/button2, all indoor stations ring For details, see Chapter 5.2...
Page 7
ABB-Welcome Terminal description Set the video mode PAL/NTSC OFF=PAL video mode ON=NTSC video mode Set default lock OFF= set (Lock-GND) as default lock ON= set (COM-NC-NO) as default lock *Default lock is controlled by “unlock” button on indoor station Plug-in clamps (a, b) for connection...
ABB-Welcome Operation Configure functions of the general call button Functions 2->OFF Call apartment 001, both 001 indoor stations ring Call apartment 002, both 002 indoor stations ring Functions 2->ON Call apartment, all 4 indoor stations (different address) ring Call apartment, all 4 indoor stations (different address) ring * If the "call forward function"...
ABB-Welcome Operation Round pushbutton with ID card reader Programming Function Command Indicated LED for door open Green Create admin card Swipe card 1x Orange Enter settings Swipe admin card 1x The system will take the first card swiped after powering up the system within 60s to be the admin card.
ABB-Welcome Operation Setting the language for the voice messages When outdoor station power is on; 1.Set outdoor station address as "0" and switch all the dip-switches to "ON." 2. Long-press the 1st button for 3s to play the voice message.
ABB-Welcome Mounting/installation Pos : 79 /Busc h-J aeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Übersc hriften (--> Fü r alle D okumente <--)/1. Ebene/M - O/Montage / Installation @ 18\mod_1302613966111_15.doc x @ 103373 @ 1 @ 1 Mounting/installation Pos : 80 /Busc h-J aeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Sic herheit (--> Fü r alle Dokumente <--)/Warnhinweis e/Sic herheit - Ni eders pannungs- und 230 V-Leitungen @ 18 \mod_1302617821491_15.doc x @ 103465 @ @ 1...
ABB-Welcome Mounting/installation General installation instructions • Terminate all branches of the wiring system via a connected bus device (e.g., indoor station, outdoor station, system device). • Do not install the system controller directly next to the bell transformer and other power supplies (to avoid interference).
ABB-Welcome Mounting/installation 7.3.5 Replace nameplate s: 94 /Busc h-Jaeger (N eustruktur)/Modul-Struktur/Onli ne-D okumentati on/Steuer module - Online-Dokumentation (--> Fü r alle Dokumente <--)/++++++++++++ Seitenumbruc h ++++++++++++ @ 9 \mod_1268898668093_0.doc x @ 52149 @ @ 1 — 18 —...
Page 19
We reserve the right to at all times make technical changes as well as changes to the contents of this document without prior notice. The detailed specifications agreed to at the time of ordering apply to all orders. ABB accepts no responsibility for possible errors or incompleteness in this document.