Related Manuals for STIEBEL ELTRON HDB-E 13 AU
Summary of Contents for STIEBEL ELTRON HDB-E 13 AU
- Page 1 OPERATION AND INSTALLATION Electronically controlled instantaneous water heater » HDB-E 13 AU » HDB-E 18 AU » HDB-E 27 AU...
-
Page 2: Table Of Contents
CONTENTS | SPECIAL INFORMATION SPECIAL INFORMATION ENVIRONMENT AND RECYCLING OPERATION WARRANTY General information �����������������������������������������3 Safety instructions ����������������������������������������������� 3 Other symbols in this documentation ����������������������� 3 SPECIAL INFORMATION Units of measurement ������������������������������������������ 3 Safety ����������������������������������������������������������3 Intended use ������������������������������������������������������ 3 General safety instructions ������������������������������������ 3 - The appliance may be used by children aged 8 Test symbols ������������������������������������������������������... -
Page 3: General Information
OPERATION General information OPERATION Symbol Meaning Material losses (appliance damage, consequential losses and environmen- tal pollution) Appliance disposal General information The chapter "Operation" is intended for appliance users and qual- f This symbol indicates that you have to do something. The ac- ified contractors. -
Page 4: Appliance Description
OPERATION Appliance description Appliance description Cleaning, care and maintenance f Never use abrasive or corrosive cleaning agents. A damp The appliance heats potable water that flows through it. When cloth is sufficient for cleaning the appliance. a DHW valve is opened, the heater starts automatically as soon f Check the taps regularly. -
Page 5: Installation
INSTALLATION Safety INSTALLATION Preparations Installation site Safety Material losses Install the appliance in a room free from the risk of frost. Only a qualified contractor should carry out installation, commis- sioning, maintenance and repair of the appliance. f Always install the appliance vertically and near the draw-off point. -
Page 6: Water Installation
INSTALLATION Installation Water installation 10. Installation f Flush the water line thoroughly. Standard installation Taps - Electrical connection in the lower section of the appliance for f Use appropriate pressure-tested taps. Open taps are not installation on unfinished walls permitted. - Water connection for installation on finished walls A safety valve is not required. - Page 7 INSTALLATION Installation f Mark out the holes to be drilled, see chapter "Installation / f Fit the flow limiter or the plastic profile washer. Specification / Dimensions and connections". f Drill the holes and secure the wall mounting bracket with Note 2 screws and 2 rawl plugs (screws and rawl plugs are not f Install the flow limiter.
- Page 8 INSTALLATION Installation Making the electrical connection WARNING Electrocution Carry out all electrical connection and installation work in accordance with relevant regulations. WARNING Electrocution The connection to the power supply must be in the form of a permanent connection in conjunction with the re- movable cable grommet.
-
Page 9: Completing The Installation
INSTALLATION Commissioning 11. Commissioning 10.2 Completing the installation f Open the shut-off valve in the cold water inlet line. WARNING Electrocution Fitting the sealing elements for the appliance cover Commissioning may only be carried out by a qualified contractor in accordance with safety regulations. 11.1 Initial start-up ≥... -
Page 10: Shutdown
INSTALLATION Shutdown 12. Shutdown 13.2 Large cross-section for electrical connection from below f Isolate all poles of the appliance from the power supply. If you use cables with a large cross-section, you can fit the cable f Drain the appliance (see chapter "Installation / grommet after the appliance has been installed. -
Page 11: Wall Mounting Bracket When Replacing An Appliance
INSTALLATION Alternative installation options 13.4 Wall mounting bracket when replacing an appliance An existing STIEBEL ELTRON wall mounting bracket may be used when replacing appliances (except instantaneous water heater DHF). f Break through the back panel of the appliance for the thread- ed stud on the installed wall mounting bracket. -
Page 12: Troubleshooting
INSTALLATION Troubleshooting 14. Troubleshooting WARNING Electrocution In order to check the appliance it must be connected to the power supply. 14.1 Indicator options for LED diagnostic traffic light Indicator options Illuminates in the event of a fault Yellow Illuminates during heating mode Green Flashing: Appliance is supplied with mains power 14.2 Fault table... -
Page 13: Maintenance
INSTALLATION Maintenance 15. Maintenance 16. Specification 16.1 Dimensions and connections WARNING Electrocution Before any work on the appliance, disconnect all poles from the power supply. Draining the appliance You can drain the appliance for maintenance work or to protect it from frost. CAUTION Burns Hot water may escape when you drain the appliance. -
Page 14: Dhw Output
INSTALLATION Specification 16.3 DHW output 16.4 Application areas / conversion table The DHW output is subject to the mains voltage, the appliance's Specific electrical resistance and specific electrical conductivity connected load and the cold water inlet temperature. The rated (see chapter "Installation / Specification / Data table"). voltage and rated output can be found on the type plate (see Standard specification chapter "Operation / Troubleshooting"). -
Page 15: Data Table
INSTALLATION | ENVIRONMENT AND RECYCLING Specification 16.7 Data table HDB-E 13 AU HDB-E 18 AU HDB-E 27 AU 234988 234989 234990 Electrical details Rated voltage Rated output 12,2 13,5 14,5 16,2 19,4 23,5 Rated current 18,5 19,5 20,2 24,7 35,6... - Page 16 Contact person: Customer Service Representative The Stiebel Eltron warranty for the unit is in addition to any rights E-mail: service@stiebel.com.au and remedies you may have under the Australian Consumer Law.
- Page 17 NOTES www.stiebel-eltron.com HDB-E AU |...
- Page 18 NOTES |HDB-E AU www.stiebel-eltron.com...
- Page 19 NOTES www.stiebel-eltron.com HDB-E AU |...
- Page 20 Deutschland Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | info-center@stiebel-eltron.de STIEBEL ELTRON GmbH & Co. KG Kundendienst Tel. 05531 702-111 | Fax 05531 702-95890 | kundendienst@stiebel-eltron.de Dr.-Stiebel-Straße 33 | 37603 Holzminden Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | ersatzteile@stiebel-eltron.de Tel.