Subscribe to Our Youtube Channel
Related Manuals for STIEBEL ELTRON HDB-E 13 Trend AU
Summary of Contents for STIEBEL ELTRON HDB-E 13 Trend AU
- Page 1 OPERATION AND INSTALLATION Electronically controlled comfort instantaneous water heater » HDB-E 13 Trend AU » HDB-E 18 Trend AU » HDB-E 27 Trend AU...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SPECIAL INFORMATION 17.4 Application areas / conversion table ����������������������� 17 17.5 Pressure drop ��������������������������������������������������� 17 OPERATION 17.6 Fault conditions ������������������������������������������������� 17 General information �����������������������������������������3 17.7 Data table �������������������������������������������������������� 18 Safety instructions ����������������������������������������������� 3 SOFTWARE COPYRIGHT Other symbols in this documentation ����������������������� 4 Units of measurement ������������������������������������������... -
Page 3: Special Information | Operation
SpECiAL iNFOrmATiON | OpErATiON General information SpECiAL iNFOrmATiON OpErATiON - The appliance may be used by children aged 3 General information and older and persons with reduced physical, The chapters "Special information" and "Operation" are intended sensory or mental capabilities or a lack of ex- for appliance users and qualified contractors. -
Page 4: Other Symbols In This Documentation
OpErATiON Safety Other symbols in this documentation WARNING Injury The appliance may be used by children aged 3 and older Notice and persons with reduced physical, sensory or mental General information is identified by the adjacent symbol. capabilities or a lack of experience and know-how, pro- f Read these texts carefully. -
Page 5: Settings
OpErATiON Settings Troubleshooting Following an interruption of the water supply Property damage problem Cause remedy To ensure that the bare wire heating system is not dam- The appliance will not There is no power. Check the fuses / MCBs in start despite the DHW your fuse box / distribu- aged following an interruption to the water supply, the valve being fully open. -
Page 6: Installation
iNSTALLATiON Safety iNSTALLATiON Test for delivery temperature performance The appliance is to be tested according to AS 3498 as a 50 °C-lim- ited water heater. The option 1 illustrated in figure A.1 of the Appendix A applies to the appliance. Safety Valve 1 Only a qualified contractor should carry out installation, commis- sioning, maintenance and repair of the appliance. -
Page 7: Preparation
iNSTALLATiON preparation Preparation Minimum clearances Installation site Property damage Install the appliance in a room that is free from the risk ≥50 ≥50 of frost. f Always install the appliance vertically and near the draw-off point. For horizontal installation, see chapter "Installation alternatives / Horizontal installation of the appliance". -
Page 8: Standard Installation
iNSTALLATiON installation 10.1 Standard installation Preparing the water connection Property damage Notice Carry out all water connection and installation work in This type of connection changes the IP rating of the ap- accordance with regulations. pliance. f Change the type plate. Cross out "IP 25" and mark the box "IP 24". - Page 9 iNSTALLATiON installation Making the electrical connection WARNING Electrocution Carry out all electrical connection and installation work in accordance with relevant regulations. WARNING Electrocution The connection to the power supply must be in the form of a permanent connection in conjunction with the re- movable cable grommet.
-
Page 10: Commissioning
iNSTALLATiON Commissioning 11. Commissioning Fit the appliance cover 11.1 Preparation Internal anti-scalding protection via jumper slot 43 °C Tmax 1 Pipe knock-out 2 Cover guides 1 Jumper for anti-scalding protection setting 3 Back panel guides 4 Fixing screw (not part of the standard delivery) Jumper position Description f Cleanly cut or break out the knock-out openings in the appli-... -
Page 11: Recommissioning
iNSTALLATiON Shutting down the system 13.1 Electrical connection from above on unfinished 11.2.1 Appliance handover walls f Explain the appliance function to users and familiarise them with how it works. f Make users aware of potential dangers, especially the risk of scalding. -
Page 12: Electrical Connection On Unfinished Walls From Below With Short Power Cable
iNSTALLATiON installation alternatives 13.2 Electrical connection on unfinished walls from 13.4 Water installation, flush-mounted below with short power cable f Seal and screw in the twin nipples (not included in standard delivery). f Reposition the mains terminal further downwards. To do this, 5 Nm undo the fixing screw. -
Page 13: Wall Mounting Bracket When Replacing An Appliance
iNSTALLATiON installation alternatives 13.7 Rotated appliance cover Property damage The cover plate of the lower back panel section must not The appliance cover can be turned the other way up for undersink bend when installed. installation. 13.5 Wall mounting bracket when replacing an appliance An existing STIEBEL ELTRON wall mounting bracket may be used when replacing appliances (except the DHF instantaneous water... -
Page 14: Service Information
iNSTALLATiON Service information 14. Service information Horizontal installation The appliance can also be mounted horizontally on the wall Overview of connections (turned 90° to the left, with the water connections on the right). The installation, water and electrical connections are described in chapters "Standard installation"... -
Page 15: Troubleshooting
iNSTALLATiON Troubleshooting 15. Troubleshooting Diagnostic Fault Cause remedy traffic light (draw-off mode) WARNING Electrocution Green flashing, No DHW; outlet One or more mains Check the fuses in To test the appliance, it must be connected to the power yellow off, temperature does power supply the distribution... -
Page 16: Maintenance
iNSTALLATiON maintenance 16. Maintenance 17. Specification 17.1 Dimensions and connections WARNING Electrocution Before any work on the appliance, disconnect all poles from the power supply. ≤ 20 This appliance contains capacitors which are discharged when disconnected from the power supply. The capacitor discharge voltage may briefly exceed > 60 V DC. -
Page 17: Wiring Diagram
Connected load in kW 38 °C DHW output in l/min. rated voltage Cold water inlet temperature 380 V 400 V 415 V 5 °C 10 °C 15 °C 20 °C HDB-E 13 Trend AU 12.2 13.5 10.7 14.5 11.5 HDB-E 18 Trend AU 16.2 10.1 12.9 11.2 14.3 19.4... -
Page 18: Data Table
This document is made of recyclable paper. the source code. Stiebel Eltron therefore provides further infor- f Dispose of the document at the end of the ap- mation regarding third supplier software that it uses under the pliance‘s life cycle in accordance with national... -
Page 19: Warranty
Contact person: Customer Service Representative The Stiebel Eltron warranty for the unit is in addition to any rights E-mail: service@stiebel-eltron.com.au and remedies you may have under the Australian Consumer Law. - Page 20 Co m f o r t t h r o u gh Te c h n o l o g y STIEBEL ELTRON GmbH & Co. KG Dr.-Stiebel-Straße 33 | 37603 Holzminden | Germany info@stiebel-eltron.com | www.stiebel-eltron.com STIEBEL ELTRON Australia Pty. Ltd.
Need help?
Do you have a question about the HDB-E 13 Trend AU and is the answer not in the manual?
Questions and answers