Sealey STW290 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS
AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE
TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP
INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! DO NOT use the digital torque adaptor if

damaged or thought to be faulty.
Ensure all workshop safety rules, regulations, and

conditions are complied with when using this digital
torque adaptor.
Maintain correct balance and footing. Ensure the floor is

not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the

working area.
After use clean with a soft dry cloth and store in a safe,

dry, childproof location.
Keep the digital torque adaptor away from magnets.

DO NOT subject the digital torque adaptor to excessive

force or shocks.
DO NOT drop or throw the digital torque adaptor.

DO NOT use digital torque adaptor unless you have

been instructed in its use by a qualified person.
DO NOT leave the digital torque adaptor in any place

exposed to excessive heat, humidity or direct sunlight.
DO NOT use organic solvents such as alcohol or

thinners to clean the digital torque adaptor.
DO NOT submerge the digital torque adapter in water or

any other liquid.
 DO NOT disassemble the digital torque adaptor.
DO NOT exceed the permitted torque value for the digital

torque adaptor.
 To ensure accurate measurement periodic re-calibration
is necessary.
2. INTRODUCTION & SPECIFICATIONS
Designed for use with a ratchet or breaker bar. Ideal for
work around the engine bay and the tightening of wheel
nuts to factory specifications. Large LCD display with
selectable readings in Nm, lb.ft, lb.in, kg-cm or kg-m and
accurate to ±2% of stated capacity. Memory stores up to
50 readings and features auto shut off after 80 seconds.
Supplied with certificate and storage case.
Specifications:
Drive: 1/2"
Accuracy: ±2%
Memory: 50
Display resolution: 0.1
Display Range: 40-200 N-m (29.5-147.5lb-ft)
Operation Mode: Peak/Trace
Unit Selection: kg-cm, kg-m, lb-in, lb-ft, Nm
Length: 75mm
Width: 45mm
Battery: 1 x CR2032
Battery Life: 55hrs (continuous operation)
Operating Ambient Temperature: -10ºC - 60ºC (13.9ºF -
139.9ºF)
Storage Temperature: -20ºC - 70ºC (-4ºF - 157.9ºF)
Operating relative humidity:15 to 90% non-condensing
Auto shut off: After 80 seconds of inactivity
INSTRUCTIONS FOR:
DIGITAL TORQUE ADAPTOR
STW290
MODEL No:
fig.1
3. INSTRUCTIONS
WARNING! DO NOT press "Mem" and "power " button

together as this will enter the unit into Calibration
Mode.
3.1 Power On (fig.2).
3.1.1 Attach the adaptor to a ratchet or breaker bar.
3.1.2 Press and release the "ON/OFF" button to turn the
adaptor on. The LCD panel shows "Trace" or "PtoP".
3.1.3 After 2 seconds the LCD panel show "0.00".
3.1.4 Tighten the nut or bolt.
3.1.5 The LCD displays the torque value measured.
Note: If not used for 80 seconds the Digital Torque Adaptor
will automatically shut off.
3.2 How to select "Unit" (fig.2).
Press "Mem" and "Peak / Trace" button together and
release to select different torque units.
Note: When you change units the target setting will also be
changed to the new units value.
This Digital Torque Adaptor contains 5 unit selections.
(kg-cm, kg-m, in-lb, ft-lb, N-m).
Memory
Button
fig.2
Buzzer Speaker
ON/OFF Button
Torque Setting Buttons
STW290 Issue No: 1 - 06/02/09
Peak/
Trace
Button