Sealey VS2075 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction Wear Eye
Manual Protection
1. SAFETY
 WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
 WARNING! Always use caution when working around fuel systems. The fuel in the fuel rail may be pressurised even if
the engine is not running.
 IMPORTANT: These instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions, or a
proprietary manual, to establish the current procedure and data, also any warnings or cautions particular to the vehicle.
 DO NOT use the set if any parts are missing or damaged.
 DO NOT use this tool for any purpose other than that for which it is designed.
 Switch off the vehicle's ignition and disconnect the battery before commencing work under the bonnet.
 You must follow the vehicle's service manual cautions when working around the air bag system. If the cautions are not followed the air
bag may deploy unexpectedly even after the ignition is turned 'OFF', resulting in personal injury.
 Never lay tools on the vehicle's battery. This may short the terminals together, causing harm to yourself, the tools, or the battery.
 Operate in a well ventilated area. DO NOT inhale fuel vapours.
 Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
 Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
 Keep children and other unauthorised persons away from the working area.
 Keep yourself, tools, and test equipment away from hot engine parts.
 Always keep a fire extinguisher that is suitable for fuel/electrical/chemical fires close by.
 NEVER smoke or have open flames near vehicle.
 Always relieve fuel pressure before disconnecting fuel lines from injectors.
 Cover fuel line fittings when connecting or disconnecting fuel lines to guard against high pressure leaks. Avoid contact with fuel.
 Clean up all fuel spills immediately and dispose of all waste according to local regulations.
 Maintain the tool components in good and clean condition for best and safest performance.
 When work on the vehicle is finished, ensure all connections on the vehicle are restored, and that there are no tools left in the engine bay.
 Replace tools in the carrying case and store in a safe, dry, childproof location.
2. INTRODUCTION
Designed for removing BMW 2.0, 2.5, 3.0 diesel fuel injectors from M47/M57 engines. Allows the removal of seized injectors without the need to
remove the cylinder head. Bridge fits perfectly on the cylinder head preventing damage to the area surrounding the injector. Also suitable for some
Land Rover, MG and Vauxhall/Opel vehicles that share the same engine.
3. APPLICATIONS
Model no: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VS2075
A : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BMW: 2 .0, 2 .5, 3 .0
pplicAtions
E c : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M47/M57
nginE odEs
4. CONTENTS
fig.1
© Jack Sealey Limited
INSTRUCTIONS FOR:
DIESEL INJECTOR PULLER - BMW M47/M57
VS2075
MODEL NO:
Key:
1: Pulling Bridge
2: Bridge Legs, short (x2)
3: Bridge Legs, long (x2)
4: Injector Force Screw Thread, Ø17mm male x 1mm pitch
5: Injector Force Screw Nut
6: Ø 27mm Injector Cap Socket
7: 10mm Security Hex Key
Original Language Version
VS2075 Issue: 1 - 31/05/17