Sealey SMS01 Instructions

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. safety
WarninG! disconnect the grinder from the mains power, and ensure the grinding wheels are at a standstill before attempting to
‰
position drill bit.
maintain the sharpener in good condition.
9
replace or repair damaged parts. use recommended parts only. non-authorised parts may be dangerous and will invalidate the warranty.
9
▲ DanGer! DO nOt use a damaged grinding wheel, to sharpen drill bits.
ensure that the correct grinding wheel is used for sharpening of drill bits.
9
WarninG! Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts.
‰
A guard or any other part that is damaged should be repaired or replaced before tool is next used. the eye shields are a mandatory
fitting when grinder is used in premises covered by the Health & safety at Work Act.
ensure adequate lighting.
9
Before each use check grinding wheels for condition. if worn or damaged replace immediately.
9
WarninG! Always wear approved eye or face protection when operating a grinder.
‰
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the working area.
9
DO nOt use the sharpener for a task it is not designed to perform.
8
DO nOt operate the grinder if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO nOt switch on the grinder whilst the wheel is in contact with the drill bit.
8
DO nOt use grinder where there are flammable liquids, solids or gases, such as paint solvents and including waste wiping or cleaning rags
8
etc.
DO nOt touch the drill bit close to the ground surface as it will be very hot. Allow to cool. the drill bit may also be very sharp.
8
DO nOt sharpen drill bits when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
When not in use switch off the grinder, disconnect from the mains power supply and clean the machine and working area.
9
2. intrODuctiOn
ideal for use with any standard bench grinder, the grinding attachment provides quick and precise sharpening of 3-19mm (1/8-3/4") Hss twist
drill bits with a 75mm minimum length. features an angle gauge with pre-sets at 41° (countersink), 49°, 59°, 68° and 88°. Also features a
rotating neck which aids grinding both sides of the drill bit. Perfect for use in any workshop or garage.
3. specificatiOn
model no: ................................................................... sms01
sizes: ........................................................ 3-19mm (1/8-3/4")
Angle Adjustment: .........41° (countersink), 49°, 59°, 68°, 88°
minimum drill Bit length: ............................................. 75mm
4. mOuntinG
Refer to fig.1
4.1. for best results grinding must take place at the axle height of the bench grinder. it may be necessary to use suitable packing to raise
the height of the grinder.
4.2. fasten grinding attachment to the bench using a bolt, washer and nut (not included).
4.3. ensure all guards are in place.
© Jack sealey limited
instructions for
Drill Bit sharpener GrinDinG attachment
sms01
model no:
Wear a mask Wear ear
protection
Original Language Version
Wear safety
footwear
sms01 | issue:2 (4,5) 29/03/18