Advertisement
3.3
How to select "Target Torque Value" (fig.2).
3.3.1 Increase (+): Press and hold the (+) button to increase
the current target value.
3.3.2 Decrease (-): Press and hold the (-) button to lower the
current target value.
3.3.3 The target will show for 10 seconds.
3.3.4 After 10 seconds the LCD display 0.00.
Note: When the digital torque adaptor get to 20% before the
target, the red LED will flash and an intermittent buzzer
will sound, warning that the target value is close.
When the target value is attained the red LED will be
illuminated and the buzzer will sound continuously.
3.4
How to set "Peak" or "Trace" (fig.2).
3.4.1 Peak: Press and release "Peak/Trace" - button when the
digital torque adaptor is on.
3.4.2 The LCD panel shows "PtoP ".
3.4.3 The LCD panel shows 0.00 after 2 seconds.
3.4.4 Trace: Press and release "Peak/Trace" - button when the
digital torque adaptor is on.
3.4.5 The LCD panel shows "trACE".
3.4.6 The LCD panel shows 0.00 after 2 seconds.
3.5
Turn Off (fig.2).
3.5.1 If the adaptor is not used for 80 seconds, it will
automatically shut down.
3.5.2 To manually turn off the digital torque adaptor press
and release the "ON/OFF" button.
3.6
Memory (fig.2).
3.6.1 To display the stored readings. Turn on the digital torque
adaptor.
3.6.2 Press and release the "Mem" button.
3.6.3 The display shows the memory number is "P01" and
then the "Torque Value".
3.6.4 Press and release the "Mem" button, again.
3.6.5 The display shows the memory number is "P02" and then
the "Torque Value".
Note: This Digital Torque Adaptor stores the last 50 torque
value readings, "P01" is the latest reading, "P50" is the
oldest.
6. DECLARATION OF CONFORMITY
Declaration of Conformity We, the sole importer into the UK, declare that the product listed below is in conformity with the
following standards and directives.
Digital Torque Adaptor
Model No: STW290
2002/95/EC RoHS Directive
2002/96/EEC WEEE Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: Call us for a copy of our latest catalogue on 01284 757525 and leave your full name and address including your postcode.
Signed by Steve Buckle
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
The construction file for this product is held by the Manufacturer and may be inspected on
request by contacting Jack Sealey Ltd.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
4. MAINTENANCE
4.1
Battery Replacement (fig.3).
4.1.1 Remove the two screws from the battery cover.
4.1.2 Lift off the battery cover.
4.1.3 Remove the battery from the holder.
4.1.4 Install new battery in the holder (with the "+" sign
facing upwards).
4.1.5 Refit the battery cover and screws.
Note: When battery is low a "
Remove the battery if stored for a long period of time.
Battery life depends on battery quality and the amount
of the lights and buzzer are used, typical life is up to 55
hours.
4.2
Calibration
4.2.1 Periodic Calibration is required for this product, contact
your Sealey dealer for details.
fig.3
6th February 2009
01284 757500
01284 703534
STW290
" icon will light.
Battery Cover
www.sealey.co.uk
Web
sales@sealey.co.uk
Issue No: 1 - 06/02/09
Advertisement
