Sealey SMS02 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. safety
the stand is an accessory for an angle grinder and is to be used to convert
9
the grinder to a cut off saw. observe all grinder manufacturers safety instructions.
the stand must be secured to a firm level surface.
9
ensure the work area is clear of debris obstructions and well lit.
9
ensure you have a stable footing (wear safety shoes) before starting to cut.
9
ensure that no flammable materials are in the area before starting work.
9
sparks from the grinder will damage paint, glass and other surfaces.
9
dO nOt wear nylon or polyester clothing whilst cutting, wear overalls which have
8
suitable resistance to fire.
dO nOt wear loose clothing, hair jewellery etc. whilst using the grinder.
8
Keep children and bystanders at a safe distance when using the tool.
9
dO nOt use the grinder without the guard being in place. The plastic guard fitted
8
to the stand is for the control of sparks only and is not designed to prevent parts of
the cutting wheel causing injury. Use a grinder fitted with the original manufacturer's
metal guard.
during assembly ensure that the metal/plastic guards are positioned between the
9
cutting wheel and the operator, so that if the cutting wheel breaks the debris will
not hit the operator.
inspect the cutting wheel for damage including chips, cracks etc before each and
9
every use.
dO nOt use a damaged wheel.
8
check that all nuts, bolts and screws are tight before use, tighten as required.
9
Keep the power cord for the grinder away from the cutting wheel.
9
use the support only with grinders with disc diameter 100mm, 115mm or 125mm.
9
use only cutting wheels with the grinder in this stand. dO nOt use wheels designed for grinding.
9
ensure the wheel is square to the base of the support.
9
ensure the material to be cut is securely held in the work clamp.
9
dO nOt try to cut materials which are too large to be safely held by the work clamp.
8
Allow the cutting wheel to come to a complete stop before attempting to remove material from the clamp.
9
Always unplug the grinder before attaching it to the stand, during any maintenance, when the stand is not in use or before dismantling.
9
2. intrOductiOn
cut-off stand with solid cast-iron base for precise vertical cutting using an angle grinder. supplied with a vice which mounts onto the base to
secure the work piece. suitable for cuts of up to 18mm. can be used with all sealey 100mm, 115mm and 125mm angle grinders, plus most
other branded grinders of the same size.
3. specificatiOn
model no ............................................................... sms02
Base size .....................................................190 x 240mm
maximum cutting depth .......................................... 18mm
4. asseMbly
4.1. fix stand (2) onto base (1) with washer (3) and tighten with screws (4).(fig.2.)
4.2. fix the top/bottom adjusting screws (7) and (13) at the top/bottom holes of stand respectively.
4.3. fix two angle grinder holders (14) and the round plastic ring (15) onto the stand by tightening the screws (5).
4.4. fix the handle (10) onto the stand with the washer (21) and nut provided.
4.5. fix the angle grinder onto the holders with screws (8) and nuts (9).
There are 3 different diameters of screws (8) and nuts (9) (M6, M8, M10). Select suitable screws that match with the fixing nut of the
© Jack sealey limited
instructions for
angle grinder stand
model no:
Wear protective Wear safety
gloves footwear
Original Language Version
sMs02
Wear protective Wear ear
clothing protection
Keep in dry area
Wear a mask
protect from rain
sms02 | issue:2 (5) 12/06/18
fig.1