Advertisement
SAFETY WARNINGS: EXTRACTING FOR
NUTRIBLASTS
• TO TURN OFF THE NUTRIBULLET AT Any time DURING blending, lift the cup off
the power base. ALWAYS ALLOW THE MOTOR TO STOP COMPLETELY BEFORE
REMOVING THE CUP/ precision extractor BLADE. ALWAYS UNPLUG THE POWER
BASE UPON COMPLETION OF use.
• Do not touch coupling gear directly with hands after use! The coupling gear in
precision extractor blade base and Power base will be hot!
• DO NOT RUN FOR MORE THAN 1 minute INTERVALs.
• DO NOT RUN FOR MORE THAN 3 CONSECUTIVE 1 MINUTE INTERVALS WITHOUT
ALLOWING the POWER BASE TO COOL TO PREVENT OVERHEATING AND ALLOW
INGREDIENTS TO SETTLE FOR 2-3 MINUTES AFTER THE 3RD EXTRACTION CYCLE.
• POWER BASE IS EQUIPPED WITH AN INTERNAL THERMAL BREAKER THAT SHUTS
OFF THE POWER BASE if THE UNIT OVERHEATS.
• IF THE POWER BASE OVERHEATS AND SHUTS OFF, UNPLUG THE POWER BASE
AND LET IT COOL FOR AN HOUR OR MORE BEFORE ATTEMPTING TO USE IT AGAIN.
POWER BASE WILL RESET WHEN THE UNIT IS powered off AND THE THERMAL
BREAKER HAS COOLED DOWN SUFFICIENTLY.
• ALLOW THE NUTRIBULLET TO COOL DOWN FOR 10 MIN AFTER 4-5 CYCLES TO
PREVENT OVERHEATING AND DAMAGING THE UNIT.
• To prevent leakage, always align and hand-tighten the precision extractor blade to the
vessel or cup prior to inverting it and placing the assembly on to the motor base.
CLEANING SAFEGUARDS
• The precision extractor blade must be cleaned immediately After each use.
• ALWAYS UNPLUG the POWER BASE PRIOR TO CLEANING, ASSEMBLING OR
DISASSEMBLING.
• NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER.
WIPE OFF ANY DEBRIS INSIDE THE POWER BASE IMMEDIATELY with warm water
TO KEEP IT IN GOOD WORKING ORDER.
• DO NOT WASH THE precision extractor BLADE IN THE DISHWASHER AS ELEVATED
TEMPERATURES CAN DAMAGE GASKET SEALS.
• THE NutriBullet CUPS AND precision extractor BLADES SHOULD NOT BE immersed
IN BOILING WATER FOR ANY REASON AS THIS WILL WARP the PLASTIC and
damage the gaskets.
• The precision extractor BLADE is SHARP! USE CARE WHEN CLEANING the
precision extractor BLADES TO AVOID INJURY! RINSE precision extractor BLADES
IMMEDIATELY AFTER EACH USE TO PREVENT DEBRIS FROM DRYING AND STICKING
TO IT. IF NECESSARY, USE a dish BRUSH TO LOOSEN ANY DEBRIS AROUND BLADE,
GASKETS AND BLADE HOUSING THREADS WITH CARE. Do not use your fingers.
• HAND WASH ONLY WITH MILD DISH SOAP AND WARM WATER (NOT HOT).
• Allow to air dry prior to proper storage.
6
• FOR TOUGH DEBRIS, FILL THE CUP ½ FULL WITH WARM (NOT HOT), MILD SOAPY
WATER. THEN, SIMPLY TWIST ON THE precision extractor BLADE, POP IT ON THE
BASE AND GIVE IT A RUN FOR 30-45 SECONDS. FOLLOW UP WITH A QUICK BRUSH.
• WHEN WASHING precision extractor BLADE, DO NOT ATTEMPT TO REMOVE THE
GASKET RING. SIMPLY HAND WASH THE precision extractor BLADE IN WARM,
MILD SOAPY WATER. ATTEMPTED REMOVAL OF THE GASKET MAY PERMANENTLY
DAMAGE THE precision extractor BLADE CONFIGURATION AND CAUSE LEAKAGE.
• We recommend replacing your Extractor Blade every 6 months or as needed for optimal
performance. To order a replacement blade, simply visit: www.nutriLIVING.COM
STUBBORN CLEANUP
If ingredients dry inside the NutriBullet Cups, make your cleanup a snap by filling
the cup about 2/3 full with warm soapy water (not hot) and screw on the Precision
Extractor Blade. Place the cup assembly on the NutriBullet Power Base for about
20-30 seconds. This will loosen the stuck ingredients, and with a light scrub and
rinse, you'll be all done.
CLEANING THE NutriBullet POWER BASE
For the most part, the Power Base doesn't really get dirty, but if you neglect to twist
the precision extractor blade on to the cup tightly, liquids can leak out and get into
the base and stick to the activator buttons.
Here's how to clean it up:
Step 1: The most important thing — UNPLUG the Power Base before cleaning!
Step 2: Use a damp rag to wipe down the inside and Outside of the Power Base.
• NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN
THE DISHWASHER.
• BLADES ARE SHARP! Never put your hands or utensils near the precision extractor
blade and never use your hands or utensils to press the activator buttons down
while the Power Base is plugged in.
7
Advertisement
