Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Maruyama EHT2300D
Summary of Contents for Maruyama EHT2300D
-
Page 2: Limited Warranty Statement
Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part Maruyama Mfg. Co., Inc. is · liable for damages to other engine components caused by the failure of warranted part still under warranty. -
Page 4: Table Of Contents
Thank you for purchasing a Maruyama product. Limited Warranty Statement ........1 California Emission Control Warranty Statement 2 Maruyama, it's distributors, and dealers want you to be Introduction ..............3 completely satisfied with your new product. Please feel free to contact your local Authorized Service Dealer for Safety ................ -
Page 5: Safety
Hedge Trimmer. Always wear hearing protection. Never use a cutting blade or replacement parts that are not approved by Maruyama. 6. Mainta in the Hedge'llimm er accordi ng to the recomm ended mainte nance interval s and •... -
Page 8: Product Description
8/ a d e • Sh a f f Ass e m b l y � - l a o p H a n d J o S h a f f G T h r o t il i g g e r •... -
Page 9: Assembly
Assembly. Assembling Engine and Drive Shaft Assembly The drive shaft, clutch drum housing and gearcase are assembled. Attach the clutch drum housing to the engine using the four M5 x 20 screws supplied with the unit. Engine M5x20Screw(4) Shaft Slip the rubber sleeve around the shaft approx i mately 9 inches (22.8 cm) from the end of the stop switch/throttle trigger assembly for an initial han... -
Page 12: Before Operation
POTENTIAL HAZARD WHAT CAN HAPPEN HOW TO AVOID TIIE HAZARD POTENTIAL HAZARD WHAT CAN HAPPEN HOW TO AVOID THE HAZARD • Gasoline contains gasses that can build up pressure inside a gas tank. • Fuel c a n b e spray e d on you when removing gas cap. -
Page 13: Mixing Gasoline And Oil
Only use a two-cycle engine oil formulated for use in SUCH AS MA RUYAMA'S STABILIZER/ high-performance, air-cooled two-cycle engines. CONDITIONER OR A SIMILA R PRODUCT. Maruyama brand 2-cycle oil is formulated for use in MARUYAMA'S STABILIZER/CONDITION high-performance, air-cooled two-cycle engines. ER IS A PETROLEUM DISTILLATE BASED . -
Page 14: Starting And Stopping
Fill the tank only to within 1/4-1/2 inch (6 mm-13 Note: Never use a mixing ratio less than mm) from the top of the tank. Avoid filling to the 50: 1 regar d less of the oil packag e top of the tank filler neck. mixing instructions. -
Page 16: Idle Speed Adjustment
WARNING the engine idle speed. POTENTIAL HAZARD If idle speed adjustment is necessary, and if WHAT CAN HAPPEN Contact your local authorized Maruyama Dealer for assistance and servicing. HOW TO AVOID THE HAZARD Operat ion cutting blades may be moving during idle speed adjustme nt Wear the recomme nded personal prote ctive equi pme nt and obse rve all safet y i nst -·... -
Page 18: Maintenance
Loosen the knob and remove the air filter cover. Remove the foam element and filter screen from the air filter cover. Clean the foam element and filter screen with warm, soapy water. Let the screen and element d completely. Apply a light coat of SAE 30 motor oil to the foam element and squeeze out all excess oil. -
Page 20: Spark Arrester
WHAT CAN HAPPEN • Muffler surfuce becomes hot when Hedge Trimmer isin operation and remains hot for some time after the engine is shut off. • Contact with hot muffler surfaces could cause a burn. • Make sure the muffler is cool before inspecting and cleaning the spark arrester. -
Page 21: Exhaust Muffler
EHT2600D Exhaust Muffler [Model:EHT2300D] Maintenance Interval The muffler should be inspected and cleaned after each I 00 hours of use. Muffler Maintenance Tail With the engine at ambient (room) temperature, loosen the knob and remove the air cleaner cover. Loosen the knob and lift off the cylinder cover. -
Page 22: Adjusting Cutting Blades
Cutting Blades Maintenance due to a lack of lubrication. To adjust the cutting blades, refer to the illustrations not covered by MARUYAMA warranty. and locate the tension screws. The gearcase and blades should be lubricated after Loosen the tension screw lockouts. Gently tum the ten... -
Page 24: Troubleshooting
Tighten throttle wire Throttle wire has come loose Engine Lacks Power or Stalls When Clean or replace air filter Cutting Dirty air filter If further assistance is required, contact your local authorized Maruyama service dealer. Specifications EHT2300D EHT2600D lbs (6.8 kg) Weight 14.5 lbs (6.6 kg)
Need help?
Do you have a question about the EHT2300D and is the answer not in the manual?
Questions and answers