Advertisement
Quick Links
Installation Guide
5-Port Gigabit Ethernet PoE Unmanaged Switch
GS305P (55W)
5-Port Gigabit Ethernet PoE+ Unmanaged Switch
GS305PP (83W)
Package contents
•
Switch model GS305P or GS305PP
•
DC power adapter
•
Detachable power cable (varies by region)
•
Wall-mount kit screws
•
Four rubber footpads
•
Installation guide
Note:
We recommend that you use Category 5e (Cat 5e) cable or higher for
Gigabit Ethernet connections.
1. Register with the NETGEAR Insight app
1. Search for NETGEAR Insight and download the latest app.
2. Set up a NETGEAR account if you do not have one.
3. Tap the menu in the upper-left corner.
4. Tap REGISTER ANY NETGEAR DEVICE.
5. Use the camera on your mobile device to scan the serial number bar code,
or enter the serial number located on the bottom of the switch.
6. Tap GO.
The switch is registered and added to your account. You can now view the
switch in the NETGEAR Insight app.
Note:
Because this is an unmanaged switch, you cannot configure or manage it
in NETGEAR Insight.
2. Connect the switch
GS305PP
Access point
Security cameras
Sample connections
Note:
The GS305PP switch supports both 802.3at (PoE+) and 802.3af (PoE).
Model GS305P supports 802.3af (PoE) only.
3. Check the LEDs
When you connect the power adapter to the switch and plug it into an electrical
outlet, the LEDs indicate the status.
The GS305P provides PoE power on ports 1–4 up to 15.4W PoE to each port, with
a PoE power budget of 55.5W across all active PoE ports.
The GS305PP provides PoE+ or PoE power on ports 1–4 up to 30W PoE to each
port, with a PoE power budget of 83W across all active PoE ports.
LED
Description
Power
Ports 1–5
left port
Ports 1–4
right port
PoE Max
The PoE Max LED indicates the status of the PoE budget on the
Router
Internet
switch:
VoIP phone
Internet
PoE
On. The switch is receiving power.
Off. The switch is not receiving power.
On.1000 Mbps link on this port.
On. 100 Mbps or 10 Mbps link on this port.
Blinking. 1000 Mbps activity on this port.
Blinking. 100 Mbps or 10 Mbps activity on this port.
Off. No link is detected on this port.
On. PoE is in use.
On. PoE halted.
Off. PoE is not in use on this port.
Off. Sufficient. More than 7W of PoE power is available.
On. Less than 7W of PoE power is available.
Blinking. At least once during the previous two minutes, less
than 7W of PoE power was available.
Advertisement
Related Manuals for NETGEAR GS305P
Summary of Contents for NETGEAR GS305P
- Page 1 LEDs indicate the status. 2. Set up a NETGEAR account if you do not have one. The GS305P provides PoE power on ports 1–4 up to 15.4W PoE to each port, with 3. Tap the menu in the upper-left corner.
- Page 2 If the PoE Max LED is solid amber, disconnect one or more PoE devices to 1. Locate the two mounting holes on the bottom panel of the switch. GS305P, and 83W for the GS305PP switch. If the power requirements for the prevent PoE oversubscription. Start by disconnecting the device from the attached powered devices (PDs) exceed the total power budget of the switch, 2.