Page 1
KNOW YOUR PRODUCT 2000W CORE DRILL • Ø150MM MAX. CAPACITY • VARIABLE SPEED • INTEGRATED COOLANT FEED INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
INTRODUCTION Congratulations on purchasing a Full Boar Core Drill. Your Full Boar Core Drill FBDCD-22150 is ideal for wet or dry core drilling downwards or horizontally in concrete, masonry and similar materials for pipe installations and anchoring or rails, fencing, etc. A safety friction clutch and integral RCD device ensure easy, safe and reliable use.
Page 5
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery operated (cordless) power tool.
Page 6
GENERAL POWER TOOL SAFETY WARNINGS (cont.) f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Page 7
DRILL SAFETY WARNINGS 1) Safety instruction for all operations a. Use the auxiliary handle. Loss of control can cause personal injury. b. Brace the tool properly before use. This tool produces a high output torque and without properly bracing the tool during operation, loss of control may occur resulting in personal injury.
Page 8
CORE DRILL SAFETY WARNINGS a. Wear ear protectors. Exposure to noise can cause hearing loss. b. Wear safety goggles or other eye protection. Drilling operations cause chips to fly. Flying particles can cause permanent eye damage. c. Bits, tools and drilling area get hot during operation. Wear gloves when touching them.
ASSEMBLY WARNING! Ensure the tool has been switched off and disconnected from the power supply and completely stopped before performing any of the following operations. Fitting the side handle (12) The side handle should be assembled to the diamond core drill prior to use. This is done by screwing the threaded end of the handle firmly (fig.
SET-UP & PREPARATION Mounting and removing a diamond core drill bit WARNING! To reduce the risk of injury, turn power off and disconnect the drill from the power source before installing and removing accessories, before adjusting or changing set- ups or when making repairs. Be sure the variable speed trigger (11) is in the off position.
Page 11
SET-UP & PREPARATION (cont.) Attaching water supply WARNING! Use core bits designed for wet use only. 1. Run water through garden hose to remove any foreign matter before attaching to the diamond core drill (fig. 5). Fig. 5 2. Set the water supply on/off tap (14) to the off position (fig.
OPERATION Variable speed trigger (11) 1. To start operation, squeeze the variable speed trigger (fig. 8). Note: The more the variable speed trigger is depressed, the faster the diamond core bit will rotate. Note: If the variable speed trigger (11) does not switch on the core drill, refer “Electric shock protection”...
Page 13
OPERATION (cont.) Electric shock protection The power cord of the core drill includes a Residual Current Device (RCD) (19), which protects the user against electric shock by interrupting the circuit when a leakage current of 10 mA or greater is detected. WARNING! Do not use the machine if the RCD (19) does not function properly.
Page 14
OPERATION (cont.) Safety clutch The core drill is fitted with a mechanical friction clutch (safety clutch) to reduce kickback. If the diamond core bit touches the reinforcing steel bar when drilling in reinforced concrete, or the motor is otherwise suddenly overloaded, the core drill may start to vibrate.
Page 15
OPERATION (cont.) KNOW YOUR PRODUCT Core drilling tips • After tightening the diamond core bit connect the core drill to the power supply and lightly press the variable speed trigger (11) to check that the diamond core bit is rotating evenly. •...
MAINTENANCE WARNING! To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. Be sure the trigger switch is in the OFF position. An accidental start-up can cause injury. •...
TROUBLESHOOTING If your tool seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your repair agent. • Core bit does not cut well If the material is too hard for the core bit, select a more suitable core bit with harder segments.
DESCRIPTION OF SYMBOLS Volts Hertz Alternating current Watts Revolutions or No load speed reciprocation per minute Millimetres Diameter Regulator compliance mark Warning Wear ear, eye and breathing Read instruction manual protection Double Insulated CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way.
CONTENTS 1 x Diamond core drill 1 x Front handle 1 x Shoulder support 4 x Shoulder support screws 1 x RCD (fitted) 1 x Water inlet hose with on/of tap (fitted) 1 x Screwdriver 1 x Carry bag Distributed by: Ozito Industries Pty Ltd AUSTRALIA (Head Office) 1-23 Letcon Drive, Bangholme Victoria, Australia, 3175...
WARRANTY YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE (see www.bunnings.com.au or www.bunnings.co.nz for store locations) WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE: Australia 1800 069 486 New Zealand 0508 069 486...
Need help?
Do you have a question about the FBDCD-22150 and is the answer not in the manual?
Questions and answers