Warranty And Liability; Declaration Of Conformity - Fein ASCS6.3 Series Original Instructions Manual

Hide thumbs Also See for ASCS6.3 Series:

User manual (126 pages)

Instruction manual (53 pages)

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

Table Of Contents

145

page of 145

/ 145
Contents
Table of Contents
Bookmarks

Table of Contents

Available languages

OBJ_BUCH-0000000372-001.book Page 19 Thursday, February 14, 2019 10:52 AM

Before any work on the machine itself, remove the bat-

tery from the power tool. If the power tool accidentally

starts, there is danger of injury.

Remove the battery only when the power tool is

switched off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture

and water. Clean contaminated battery terminals and

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended

for your power tool. When working with and charging

incorrect, damaged, repaired or reconditioned batter-

ies, imitations or other brands, there is danger of fire

and/or explosion.

Follow the safety warnings in the operating instructions

of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a stand-

ardised test given in EN 62841 and may be used to

compare one tool with another. It may be used for a

preliminary assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However, if the tool is

used for different applications, with different accesso-

ries or poorly maintained, the vibration emission may

differ. This may significantly increase the exposure level

over the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool

is switched off or when it is running but not actually

doing the job. This may significantly reduce the expo-

sure level over the total working period.

Identify additional safety measures to protect the oper-

ator from the effects of vibration such as: maintain the

tool and the accessories, keep the hands warm, organi-

sation of work patterns.

Operating Instructions.

Adjust the rotation selector switch only when the

machine is at a complete stop.

To avoid accidental starting, e. g., during transport, set

the rotation selector switch to the centre position.

When overheated, the machine runs with short, low-

power impulses. Allow the machine to cool down at

no-load speed.

For reliable working results, always carry out screw-

driving operations using the depth stop.

Electronic torque shut-off (see pages 6 – 7).

The electronic torque shut-off can be used when work-

ing without depth stop.

Adjust the torque only when the machine is at a com-

plete stop.

The motor switches off when reaching the set torque

and an audio signal sounds. After the shut-off has taken

place, release the on/off switch and press it again for the

next screwdriving operation.

The audio signal can be switched on and off.

The electronic shut-off is deactivated when working in

the "

" torque level.

To achieve good working results, press the power tool

with sufficient force against the screw.

Handling the battery.

Store, operate and charge the battery only using FEIN

battery chargers within the battery operating-tempera-

ture range between 5 °C – 45 °C (41 °F – 113 °F). At

the beginning of the charging procedure, the battery

temperature must be within the battery operating-tem-

perature range.

LED indica-

Meaning

tor

1 – 4 green

Percentage of

LED

charge condi-

tion

Continu-

Battery is

ous red

almost empty

light

Red flash-

Battery is not

ing light

ready for

operation

The real percentage of the battery charge condition is

only indicated when the power tool motor is stopped.

The electronics automatically switch off the motor

prior to the battery being deep discharged.

Repair and customer service.

When working metal under extreme oper-

ating conditions, it is possible for conductive

dust to settle in the interior of the power

tool. Blow out the interior of the power tool via the

ventilation slots frequently with dry and oil-free com-

pressed air.

Products that have come into contact with asbestos

may not be sent in for repair. Dispose of products con-

taminated with asbestos according to the applicable

country-specific regulations for such disposal.

The current spares parts list for this power tool can be

found on our website at www.fein.com.

If required, you can change the following parts your-

self: application tools, depth stop, battery, belt clip