Page 2
No part of this manual may be reproduced, stored in a retrieval system, or transmit- ted in any form or by any means, electronic, mechanical, photocopying, micro-film- ing, recording, or otherwise, without the prior written permission of Eaton Industries GmbH, Bonn, Germany.
Page 3
Danger! Dangerous electrical voltage! Before commencing the installation • Disconnect the power supply of the device. • Wherever faults in the automation system may cause damage to persons or property, external measures must • Ensure that devices cannot be accidentally retriggered. be implemented to ensure a safe operating state in the •...
Installation requires a qualified electrician 0.3 Additional documents For further information, see the following documentation: • Instruction leaflet IL05013039Z2018_06 WARNING Make sure you always use the latest documentation. It can be downloaded from the product at: www.eaton.eu/esr5 ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
Warns of the possibility of hazardous situations that could result in serious injury or even death. DANGER Warns of hazardous situations that result in serious injury or death. 0.4.3 Tips → Indicates useful tips. 0.5 Ordering data ESR5-NOS-31-230VAC safety relay: Catalog No. 153152 ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
Risk of damage to equipment due to noise emissions When operating relay modules the operator must meet the requirements for noise emission for electrical and electronic equipment (EN 61000-6-4) on the contact side and, if required, take appropriate measures. ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
2 Description 2 Description The ESR5-NOS-31-230VAC safety relay can be used in safety circuits according to EN 60204-1 and IEC 61508. With this switching device, circuits are interrupted in a safety-oriented manner. Control is via a single channel, either with automatic or manual start circuit.
LED status indicator, green - K2 f LED status indicator, green - K1 g LED status indicator, green - Power h S11/S12 - input circuit i A1/A2 - supply voltage connection j S33, S34, S35 - start circuit (activating circuit) ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
No fault detection on initial start, only on first new demand. ● ○ ● Enable contact(s) of K1 faulty. Fault with ● ● ○ Enable contact(s) of K2 faulty. Replace safety relays. internal cause ● ○ ○ Enable contact(s) of K1 and K2 faulty. ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
7.2 Single-channel safety door monitoring with automatic activation • Automatic activation • Suitable up to category 1, PL c (EN ISO 13849-1), SILCL 1 (EN 62061) 230 V 23 33 41 ESR5-NOS-31-230VAC 14 24 34 42 Figure 5: Single-channel safety door monitoring ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
6 A (24 V DC) 5 A (230 V AC) Switching capacity (3600 cycles/h) 3 A (24 V (DC-13)) 3 A (230 V (AC-15)) Output fuse 10 A gL/gG NEOZED (enabling current paths) 6 A gL/gG NEOZED (signaling current path) ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
Page 17
Safety data Stop category according to IEC 60204-1 Safety parameters for IEC 61508 - High demand 2.42 x 10 per hour Demand rate < 12 months Proof test interval 240 months Duration of use 240 months ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
Page 18
Safety characteristic data according to EN ISO 13849 Category Performance Level Duration of use 240 months The specifications apply assuming the following calculation basis: 300000 (at 5 A DC-13) Cycles 8760 per year Safety characteristic data according to EN 62061 SILCL ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
Classification of the ability of safety functions to meet a safety demand Safety integrity level SILCL SIL claim limit SRCF Safety-related control function SRECS Safety-related electrical control system (Safety-related electrical, electronic, and programmable electronic control system) Safety-related part SRP/CS Safety-related parts of control system ESR5-NOS-31-230VAC 12/19 MN049013EN www.eaton.com...
Need help?
Do you have a question about the ESR5-NOS-31-230VAC and is the answer not in the manual?
Questions and answers