Group B Functions - List - Yamaha CBX-K2 Owner's Manual

Group B Functions — List
Key Panel Name
C1 SEQUENCER SONG SELECT
C#1 TIME SIGNATURE TOP
D1 TIME SIGNATURE BOTTOM
D#1 MEASURE
E1 - VOICE MAP
F1 - POLY/MONO
F#1 RESET RESET CONTROL
G1 SOUND OFF ALL CH
G#1 TG300B
A1 SYSTEM CHANNEL MERGE
A#1 DEVICE NUMBER
B1 TOUCH SENSITIVITY
C2 - RPN
C#2 - CONTROLLER
D2 - NRPN
D#2 WHEEL ASSIGN DATA DENSITY
E2 - MSB 1ST/LSB 1ST
F2 - FOOT SW ASSIGN
F#2 - -
G2 - -
G#2 - PB DENSITY
A2 SLIDER ASSIGN DATA DENSITY
F#3 - SELECT B
Footnotes
*1 Depending on the selected message or the particular device that is
connected to the CBX-K2, there may be no response. Refer to the
owner's manual of the device for details.
*2 The Time Signature Top value is selected in the following order: 4, 5,
6, ... 15, 16, 1, 2, 3, 4, etc. ("4" is used as the starting point, since
that is the most commonly used Top value.) The order for the Time
Signature Bottom values is 4, 8, 16, 4, etc.
*3 The range for the Measure function depends on the currently set Time
Signature. When set to 4/4, the range is 1 – 999; when set to 8/4 or
16/8, the range is 1 – 512. The absolute maximum is 999.
28
Function name Operation (press and hold [SHIFT] )
C ç
Song Select +
(song number)
C ç
Time Signature Top +
(numerator)
C ç
Time Signature Bottom +
(denominator)
C ç
Measure Number +
(measure number)
C ç
Voice Map +
(Map number)
C ç
Poly/Mono +
C ç
Reset All Controllers +
C ç
All Sound Off (all channels) +
TG300B Reset C + ç
C ç
Merge On /Off +
(each channel) (channel number)
C ç
Device Number +
(device number)
C ç
Touch Sensitivity +
L
(value)
C ç
Controller Direct Data Send +
(RPN) {(control value)
C ç
Controller Direct data Send +
(controller number) L
Controller Direct Data Send C + ç
L
(NRPN)
C ç
Data Density (Wheel) +
(density value)
C ç
MSB/LSB invert +
C ç
Footswitch Assign +
... (press repeatedly)
- -
- -
C ç
Data Density +
(Pitch Bend Wheel) (density value)
C ç
Data Density (Slider) +
(density value)
C ç
Single-byte Data Send +
*4 • The channel number can only be entered as a hexadecimal value (1
– F, 0).
• Using system exclusive messages to turn Merge on or off can only
be done for all channels (as in the corresponding Group A
function).
*5 When Fixed Velocity (in Group A) is set to a value other than 0, the
Touch Sensitivity function is inactive. The following table shows the
velocity range for the minimum, medium, and maximum Touch
Sensitivity settings.
œ
L
¡
{ }...(press repeatedly)
®
{ }...(press repeatedly)
†
L
¥
L
ø
å
ß
™ L
ƒ
©
L
˙
A L
(MSB) (LSB)
L
}
S
(controller number)
{(controller value) L }
D (MSB) (LSB)
L
{(controller value) }
£
L
˚
¬
{ }
§
L
£
L
L
{(single-byte data)
Operation Examples
*9
*9
*9
-
-
} *9