Group A Functions - List - Yamaha CBX-K2 Owner's Manual

Group A Functions — List
Key Panel Name
C1 SEQUENCER STOP
C#1 CONTINUE
D1 START
D#1 TEMPO
E1 PROGRAM BANK SELECT
F1 PROGRAM CHANGE
F#1 RESET GM ON
G1 ALL SOUND OFF
G#1 XG ON
A1 SYSTEM MERGE ON/OFF
A#1 MIDI CH
B1 FIXED VELOCITY
C2 WHEEL ASSIGN RPN
C#2 CONTROLLER
D2 NRPN
D#2 DRUM NUMBER
E2 TRANSPOSE Q
F2 W
F#2 SLIDER ASSIGN RPN
G2 CONTROLLER
G#2 NRPN
A2 DRUM NUMBER
D#3 DISPLAY PROGRAM CHANGE
E3 BANK MSB
F3 BANK LSB
Footnotes
*1 The operation steps in braces ({}) can be repeated or re-entered as
long as C is held.
*2 Depending on the selected message or the particular device that is
connected to the CBX-K2, there may be no response. Refer to the
owner's manual of the device for details.
*3 Be careful not to press the connected footswitch when footswitch is
assigned to "SUS"; the operation cannot be executed while the
footswitch is pressed.
*4 When Tempo is assigned to the Assignable Wheel or Slider, this
setting is ignored. When the Assignable Wheel or Slider is set to a
26
Function name Operation (press and hold [SHIFT])
C Q
Stop +
C W
Continue +
C E
Start +
Tempo C + R
C T
Bank Select +
C Y
Program Change +
(program change number)
C U
GM System On +
C I
All Sound Off +
(current channel)
C O
XG System On +
C P
Merge On/Off(all channel) +
C {
MIDI Transmit channel +
C }
Fixed Velocity +
C A
Wheel Assign (RPN) +
C S
Wheel Assign +
(controller number)
C D
Wheel Assign (NRPN) +
Drum Number (Wheel) Select the desired drum sound from the keyboard (page 23)
then press
C G
Transpose Down +
....(press repeatedly)
C H
Transpose Up +
....(press repeatedly)
C A
Slider Assign (RPN) +
C S
Slider Assign +
(controller number)
C D
Slider Assign (NRPN) +
Drum Number (Slider) Select the desired drum sound from the keyboard (page 23)
then press
C Y
Display Program Change +
C ¢
Display Bank Select MSB +
C ¶
Display Bank Select LSB +
function other than Tempo, the current value is effective. The range
for this function is 20 – 300 bpm; when the Wheel or Slider is set to
control Tempo, the range is slightly narrower: 28 – 282 bpm. When
this is set to 0, "oFF" is shown in the display.
*5 The entry order of the MSB and LSB values can be changed by using
the MSB 1ST/LSB 1ST in Group B.
*6 The actual program change number transmitted by the CBX-K2 is the
displayed number minus one. For example, program number 001 on
the display is actually transmitted as 000.
*7 The value can also be easily increased or decreased. First, make sure
that the display is set appropriately (to Program Change or Bank
(tempo value) L
L
(MSB) (LSB)
L
L
L
L
(channel number)
L
(velocity value)
L
(MSB) (LSB)
L
(controller number)
L
(MSB) (LSB)
C F L
+
G
{ }
H
{ }
L
(MSB) (LSB)
L
(controller number)
L
(MSB) (LSB)
C F L
+
L
L
L
*1 Operation Examples