Operation - Renkforce 1493869 Operating Instructions Manual

Before installing the product make sure that the installation surface is dry and free of
any dirt, grease or other contaminations.
• Select a smooth and flat surface. Clean the surface thoroughly and let it dry completely,
otherwise the adhesive tape will come off the surface.
• Peel the film of the adhesive tape located on the back side of the strip.
• Gently press the strip against the surface.
• Connect all the components following the sequence shown on the drawing below. Make
sure to top align the arrow on the connection cable with the +5V marking on the LED strip,
otherwise the strips will not illuminate.
3
E D
+
4
Operating elements
1 LED strip
2 Connection cable

Operation

Using remote control
• This remote control comes with a pre-installed battery. To activate the remote control, remove
the plastic tag.
• Point the infrared sensor on the remote control in the lamp direction.
The remote control features a range of max. 5-7 m. Any objects located between the
remote control and the lights will reduce the range.
Button Feature
Increase brightness
Decrease brightness
ON Switch light on
OFF Switch light off
R Select RED colour
G Select GREEN colour
B
Select BLUE colour
W
Select WHITE colour
FLASH 3 colours alternating change (jumping effect)
STROBE 3 colours gradual change in colours
FADE 7 colours gradual change in colours
SMOOTH 7 colours alternating change
Coloured
Select desired pre-set colour temperature
buttons
2 1
C
1
3 USB cable with control unit and IR receiver
4 Remote control (incl. CR2025 battery)
Care and cleaning
a) Inserting/changing the battery
• Remove the battery holder from the battery
compartment as shown.
• Insert a new battery (type CR2025).
• Make sure the polarity is correct. It is shown
on the back of the remote control.
• Slide the battery holder back into the battery
compartment until it clicks into place.
Replace the batteries as soon as the lights do no longer respond to commands from
2
the remote control.
B
b) Cleaning
• Apart from the occasional battery change for the IR remote control, the product is
A
maintenance-free. The built-in LED bulbs are permanently installed; they cannot be replaced.
• Disconnect the product from the power supply before cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the outside of the product with a soft, dry, fiber-free cloth.
• Do not immerse the product in water.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations. Remove any inserted batteries and dispose of
them separately from the product.
b) Batteries
As the end user, you are required by law (Battery Ordinance) to return all used
batteries; disposal of them in the household waste is prohibited!
Contaminated batteries are labelled with this symbol to indicate that disposal in the
domestic waste is forbidden. The designations for the heavy metals involved are:
Cd = Cadmium, Hg = Mercury, Pb = Lead (name on batteries, e.g. below the trash
icon on the left).
Used batteries can be returned to collection points in your municipality, our stores or wherever
batteries are sold.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
a) General
Power supply ........................................................................ USB port, 5 V/DC, max. 0.5 A
Power consumption .............................................................. 1.4 W
Protection class .................................................................... Class III
Operating conditions ............................................................. 0 to +45 ºC, 0 – 90 % RH
Storage conditions ................................................................ 0 to +45 ºC, 0 – 90 % RH
b) LED strip (each)
Length................................................................................... 0.5 m
Number of LEDs....................................... ............................ 15x LED
Dimensions (L x W) ............................................................... 500 x 10 mm
Weight ................................................................................... approx. 16 g
c) Remote control
Operational range ................................................................. max. 4.5 m
Power supply ........................................................................ 1 x 3 V/DC button cell,
Dimensions (W x H x D) ........................................................ 52 x 7 x 85 mm
Weight ...................................................................................approx. 18 g (with battery)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
type CR2025
1493869_v3_0120_02_dh_m_en