Related Manuals for Pepperl+Fuchs KCD2-STC-1.SP
Summary of Contents for Pepperl+Fuchs KCD2-STC-1.SP
- Page 1 PROCESS AUTOMATION MANUAL Functional Safety SMART Transmitter Power Supply KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) ISO9001...
- Page 2 Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) With regard to the supply of products, the current issue of the following document is applicable: The General Terms of Delivery for Products and Services of the Electrical Industry, published by the Central Association of the Electrical Industry (Zentralverband Elektrotechnik und Elektroindustrie (ZVEI) e.V.) in its most recent version as well as the supplementary clause: "Expanded reservation of proprietorship"...
-
Page 3: Table Of Contents
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Content Introduction ........... 4 Content of this Document. -
Page 4: Introduction
Additionally, the following parts may belong to the documentation, if applicable: • EU-type examination certificate • EU declaration of conformity • Attestation of conformity • Certificates • Control drawings • FMEDA report • Assessment report • Additional documents For more information about Pepperl+Fuchs products with functional safety, see www.pepperl- fuchs.com/sil. -
Page 5: Safety Information
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Introduction Safety Information Target Group, Personnel Responsibility for planning, assembly, commissioning, operation, maintenance, and dismounting lies with the plant operator. Only appropriately trained and qualified personnel may carry out mounting, installation, commissioning, operation, maintenance, and dismounting of the product. The personnel must have read and understood the instruction manual and the further documentation. -
Page 6: Symbols Used
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Introduction Symbols Used This document contains symbols for the identification of warning messages and of informative messages. Warning Messages You will find warning messages, whenever dangers may arise from your actions. It is mandatory that you observe these warning messages for your personal safety and in order to avoid property damage. -
Page 7: Product Description
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Product Description Product Description Function KCD2-STC-1(.SP) This signal conditioner provides the galvanic isolation between field circuits and control circuits. The device supplies 2-wire transmitters in the field, and can also be used with current sources. The device transfers the analog input signal to the control side as an isolated current value. Bi-directional communication is supported for SMART transmitters that use current modulation to transmit data and voltage modulation to receive data. - Page 8 Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Product Description KCD2-STC-Ex1-Y1 This isolated barrier is used for intrinsic safety applications. The device supplies 2-wire transmitters in the hazardous area. The device transfers the analog input signal to the non-hazardous area as an isolated current value.
-
Page 9: Interfaces
Safety relevant interfaces: input I, output I • Non-safety relevant interfaces: none The HART communication is not relevant for functional safety. Note! For corresponding connections see datasheet. Marking Pepperl+Fuchs GmbH Lilienthalstraße 200, 68307 Mannheim, Germany Internet: www.pepperl-fuchs.com KCD2-STC-1(.SP) Up to SIL 2 KCD2-STC-Ex1(.SP)(-Y1) HiC2025(Y1) -
Page 10: Planning
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Planning Planning System Structure 3.1.1 Low Demand Mode of Operation If there are two control loops, one for the standard operation and another one for the functional safety, then usually the demand rate for the safety loop is assumed to be less than once per year. -
Page 11: Assumptions
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Planning Assumptions The following assumptions have been made during the FMEDA: • Failure rate based on the Siemens standard SN29500. • Failure rates are constant, wear is not considered. • External power supply failure rates are not included. •... -
Page 12: Safety Function And Safe State
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Planning Safety Function and Safe State Safety Function The device transfers analog signals from the input to the output with a tolerance of 2 % related to the full signal range. Use the following DIP switch settings for safety-relevant applications: DIP Switch Settings KCD2-STC-(Ex)1(.SP)(-Y1) Function Current source 4 mA to 20 mA... -
Page 13: Characteristic Safety Values
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Planning Characteristic Safety Values Parameters Characteristic values Assessment type Full assessment Device type Mode of operation Low demand mode or high demand mode Safety function Signal transfer 122 FIT 172 FIT 45 FIT 122 FIT ... -
Page 14: Useful Lifetime
As noted in DIN EN 61508-2:2011 note N3, appropriate measures taken by the manufacturer and plant operator can extend the useful lifetime. Our experience has shown that the useful lifetime of a Pepperl+Fuchs product can be higher if the ambient conditions support a long life time, for example if the ambient temperature is significantly below 60 °C. -
Page 15: Mounting And Installation
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Mounting and Installation Mounting and Installation Mounting and Installing the Device 1. Observe the safety instructions in the instruction manual. 2. Observe the information in the manual. 3. Observe the requirements for the safety loop. 4. Connect the device only to devices that are suitable for this safety application. 5. -
Page 16: Operation
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Operation Operation Danger! Danger to life from missing safety function If the safety loop is put out of service, the safety function is no longer guaranteed. • Do not deactivate the device. • Do not bypass the safety function. •... - Page 17 Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Operation Proof Test Procedure The proof test reveals almost all possible dangerous faults (diagnostic coverage > 90 %). 1. Put out of service the entire safety loop. Protect the application by means of other measures. 2. Prepare a test set-up, see figures below. 3.
- Page 18 Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Operation Active Passive Multimeter input input HiC2025 Input sensor Input sensor (2-wire Tx (4-wire Tx Current output or loop powered) externally Voltage output or powered) Current sink 4 mA to 20 mA Logic 4 mA to 20 mA solver analog input...
-
Page 19: Maintenance And Repair
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Maintenance and Repair Maintenance and Repair Danger! Danger to life from missing safety function Changes to the device or a defect of the device can lead to device malfunction. The function of the device and the safety function is no longer guaranteed. Do not repair, modify, or manipulate the device. -
Page 20: List Of Abbreviations
Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) List of Abbreviations List of Abbreviations Emergency Shutdown Failure In Time in 10 FMEDA Failure Mode, Effects, and Diagnostics Analysis Probability of safe failure Probability of dangerous detected failure Probability of dangerous undetected failure ... - Page 21 Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Notes...
- Page 22 Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Notes...
- Page 23 Functional Safety KCD2-STC-(Ex)1(.SP)(-Y1), HiC2025(Y1) Notes...
- Page 24 PROCESS AUTOMATION – PROTECTING YOUR PROCESS Worldwide Headquarters Pepperl+Fuchs GmbH 68307 Mannheim · Germany Tel. +49 621 776-0 E-mail: info@de.pepperl-fuchs.com For the Pepperl+Fuchs representative closest to you check www.pepperl-fuchs.com/contact www.pepperl-fuchs.com Subject to modifications DOCT-1596G Copyright PEPPERL+FUCHS • Printed in Germany 08/2018...