Ce Conformity Declaration; Disposal Notes; Guarantee / Liability Exclusion - Multiplex AntiFlash 70 Operating Instructions Manual

3) Switch the transmitter ON.
4) If the receiver is powered by one or more separate receiver
batteries: switch the receiving system ON.
5) Connect the flight battery to the BATT end of the AntiFlash 70.
Result:
The safety switch features an annular light which glows red
(Fig. 6), indicating the present status of the switch:
The magnet is in place.
The power system is connected, but has not yet been
"armed".
The motor cannot be started yet.
If the receiving system is powered exclusively via the
speed controller (BEC mode): the receiving system is not
yet operating.
6) Withdraw the magnet (with MULTIPLEX pennant) from the
Professional safety switch.
Result:
The annular light on the safety switch glows green (Fig. 7),
indicating the present switch status:
The magnet is withdrawn.
The power system is now "armed" without any sparking.
The motor can be started. Caution - injury hazard: the
motor could start running.
If the receiving system is powered exclusively via the
speed controller (BEC mode): the receiving system is
now operating.
7) After the flight: replace the red magnet (with MULTIPLEX
pennant) on the Professional safety switch, then disconnect
the flight battery from the AntiFlash 70. If you are using
separate receiver batteries, switch the receiving system OFF
at this point. Finally switch the transmitter OFF.
8. CE
CONFORMITY DECLARATION
These devices have been approved in accordance with
current European harmonised directives.
This means that you possess a product whose design and
construction fulfil the protective aims of the European Com-
munity intended to ensure the safe operation of equipment.
9. D N
ISPOSAL OTES
Electrical equipment marked with the cancelled waste
bin symbol must not be discarded in the standard
household waste; instead it should be taken to a
suitable specialist disposal system.
In the countries of the EU (European Union) electrical
equipment must not be discarded via the normal
domestic refuse system (WEEE - Waste of Electrical and
Electronic Equipment, Directive 2002/96/EG). You can take
unwanted equipment to your nearest local authority waste
collection point or recycling centre. There the equipment will be
disposed of correctly and at no cost to you.
By returning your unwanted equipment you can make an
important contribution to the protection of the environment!
10. G / L
UARANTEE
The company MULTIPLEX Modellsport GmbH & Co.KG accepts
no liability of any kind for loss, damage or costs which are due to
the incorrect use and operation of this product, or which are
connected with such operation in any way. Unless the law
expressly states otherwise, the liability on the part of MULTI-
PLEX Modellsport GmbH & Co.KG to pay damages, regardless
of the legal argument employed, is limited to the invoice value of
those products supplied by MULTIPLEX Modellsport GmbH &
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Operating instructions for AntiFlash 70,
"Micro" and "Professional" safety switch
E
IABILITY XCLUSION
Co.KG which were directly involved in the event in which the
damage occurred. This does not apply if liability is incurred
according to statutory law on account of intentional or gross
negligence.
We guarantee our products in accordance with the currently
valid statutory regulations. If you wish to make a claim under
guarantee, your initial course of action should always be to
contact the dealer from whom you purchased the equipment.
The guarantee does not cover faults and malfunctions which are
caused by the following:
Incorrect or incompetent use
Maintenance carried out incorrectly, belatedly or not at all, or
not carried out by an authorised Service Centre
Incorrect connections
The use of accessories other than genuine MULTIPLEX
items
Modifications or repairs which were not carried out by
MULTIPLEX or by an authorised MULTIPLEX Service
Centre
Accidental or intentional damage
Defects due to normal wear and tear
Operation of the unit outside the limits stated in the Speci-
fication
Operation of the unit in conjunction with equipment made by
other manufacturers.
Page 3/4