Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bose Cinemate Cinemate Digital Home Theater Speaker System
Summary of Contents for Bose Cinemate Cinemate Digital Home Theater Speaker System
- Page 1 CINEMATE ™ D I G I T A L H O M E T H E A T E R S P E A K E R S Y S T E M...
- Page 2 RTTE Directive 99/5/EC (R+TTED).The complete Declaration of Conformity can be found on <www.bose.com>. Additional safety information See the additional instructions on the Important Safety Information sheet enclosed in the shipping carton. ® ® ™ module in the Bose CineMate speaker system.
-
Page 3: Table Of Contents
........ -
Page 4: Introduction
• An Interface module that provides simple audio connections to your TV and receives IR remote control signals Setup help The CineMate digital home theater speaker system easily connects to your TV and other home theater equipment. To help you set up your CineMate system, the following items are provided: •... -
Page 5: Setup
Copy that number onto your product registration card and in the space provided on page 4. Figure 1 Carton contents Large rubber feet * The appropriate power cord for your region is provided. ® dealer immediately. For Bose contact information, refer Acoustimass module Batteries 8-foot power cord* 15-foot speaker 6-foot stereo... -
Page 6: Selecting A Location For Your Cinemate
The Interface module receives commands from the universal remote control and provides audio input connections for the CineMate to turn the speakers on, change the volume, and mute or turn off the speaker system. • Position the Interface module on a flat surface near the TV and other home theater equipment (Figure 2). -
Page 7: Positioning The Speakers
You can obtain additional rubber feet (PN 178321) from Bose in the carton. Note: The speakers can be mounted on Bose brackets, table stands, or floor stands. For ordering information, refer to “Accessories” on page 22. Additional or longer cables may also be ordered. -
Page 8: Positioning The Acoustimass ® Module
YSTEM ETUP • Set the speakers on their bottom surfaces, only, with the Bose Figure 4 Recommended speaker orientation • Aim the speakers straight ahead into the listening area (Figure 5). Do not place the speakers at an angle. Angling one or both speakers into or away from the listening area sig- nificantly alters system performance. -
Page 9: Making System Connections
English Español Français • Aim the port of the module into the room or along the wall to prevent over-powering bass. • Stand the Acoustimass (Figure 7). • Attach the large rubber feet to the bottom of each foot on the module. The rubber feet provide increased stability and protection from scratches. -
Page 10: Connecting The Interface Module To The Acoustimass Module
Figure 10 Left and right speaker connections Note: A longer speaker cable can be ordered from Bose, if you need it. To contact Bose, refer to the address sheet included in the carton. Connecting the Interface module to the Acoustimass On the Acoustimass module, insert the Interface module connector into the input jack (Figure 11). -
Page 11: Connecting Your Tv To The Interface Module
English Español Français Connecting your TV to the Interface module After setting up the system speakers and Interface module, connect the audio output of your TV to the TV AUDIO input jacks on the Interface module, using the supplied stereo cable (Figure 12). -
Page 12: Standby And Power Led Indicators
Provided on 220-240V rated systems only Note: Bose recommends using a safety agency-approved surge protector on all electronic equipment. Voltage variations and spikes can damage electronic components in any system. A quality suppressor can eliminate the vast majority of failures attributed to surges and may be purchased at electronics stores. -
Page 13: Setting Up Your Tv For The Cinemate
(see “Turning off the TV internal speakers”), exit the audio menu, and adjust the TV volume to about 80% of the highest volume. speaker system button and selecting menu item, select YSTEM ETUP speaker system, the and exit the menu. -
Page 14: Installing Or Replacing The Remote Batteries
2. Locate the five-digit device code(s) for your brand of TV and start with the first one. 3. Press and hold Setup on the remote until all five source buttons light up. Français Battery compartment cover Español English ™ speaker system can be... -
Page 15: To Control A Combination Device
English Español Français 4. Press the TV source button. Only the TV source button will remain lit. TV source button 5. On the remote keypad, enter the first device code for your brand of TV. 6. Check that the TV source button blinks twice and turns off after the code is entered. 7. -
Page 16: Peration
Using the remote to watch a DVD 1. Press On-Off to turn on the CineMate speaker system. The green LED on the front of the Interface module will light. 2. Press TV On-Off to turn on your TV. -
Page 17: Remote Control Operating Guide
English Español Français Remote control operating guide Note: In order to control your TV and other audio/video sources using the remote control, you must first program the remote with a device code for each source. See “Setting up the remote to control other sources”... - Page 18 PERATION Remote control operating guide – cont. Menu and program selection Note: The menu and program selection buttons will control only one source at a time, depending on which source is selected on your remote (TV, CBL-SAT, DVD, VCR, or AUX). Français •...
- Page 19 English Español Français Remote control operating guide – cont. Play options Note: The functionality of the play options buttons may vary depending on the brand of your device(s). Some features may not be supported by your brand. See your owner’s guide(s) for more information.
- Page 20 PERATION Remote control operating guide – cont. Play options – cont. Cable-specific buttons TeleText buttons (Europe only) Cable-specific or TeleText buttons Français • Switches between VCR and TV as the current video input source on your VCR or VCR combination device. •...
-
Page 21: Verifying A Device Code
English Español Français Verifying a device code When you programmed your remote during setup, a device code for each source was stored in the remote. If you need to verify which code has been programmed for a particular source, follow the steps below. If you need to reprogram a device code, see “Setting up the remote to control other sources”... -
Page 22: Are And Aintenance
For further information or to order mounting brackets, stands, or cable adapters, contact your Bose dealer. Or, to call Bose directly, refer to the address sheet included in the carton. Troubleshooting... -
Page 23: Customer Service
• Turn off your TV’s internal speakers. See “Turning off the TV internal speakers” on page 13. from the TV • Turn down the TV volume. Customer service For additional help in solving problems, contact Bose address sheet included with the system. Technical information Power rating...