DEUCE
DUAL HEAD W600
TECHNICAL SPECIFICATIONS
INPUT VOLTAGE ........................10 to 30 Volts DC.
INPUT CURRENT .......................0.5A @ 12.8V, 0.45A @ 25.6V
LIGHT OUTPUT ...........................AMBER: 160+ LUMENS
CABLE LENGTH ..........................7 FT. (HEAD A), 4FT. (HEAD B)
LED ELEMENTS ..........................4 (EACH HEAD)
FLASH PATTERNS ......................16 (8 Standard, 8 optional cycle)
MAX NUMBER OF SYNC'D HEADS ... 64
WARRANTY PERIOD ..................5 YEARS
1.50"
4.89"
INPUT MABLE: 4FT
POWER MODULE
CONNECTOR SEALING
920-9121-00 REV. C
BLUE: 155+ LUMENS
RED: 123+ LUMENS
WHITE: 660+ LUMENS
DIMENSIONS
1.28"
LED HEAD
HEAD A
HEAD B
LED HEAD
CABLES:
4FT, 7FT
Drill a 1" diameter hole in the reflector of the lens assembly.
A 1" hole saw is typically used. The HIDE-A-LED™ may be used as a
template to mark the location of the two screw holes. The W600 may
be mounted in either the back surface, bottom or sides of a reflector.
Drill pilot holes with a 7/64" drill bit. Install the HIDE-A-LED™ into the
lens assembly using the supplied gasket and screws. If the mount-
ing surface is curved additional sealing may be necessary. Use RTV
Silicone sealant if needed.
LOCATE LED HEAD AT LEAST 1" AWAY
FROM ANY FACTORY BULB!
REFLECTOR
GASKET
! HOT !
THE HEATSINK WILL BE HOT AFTER RUNNING
FOR AN EXTENDED PERIOD. DO NOT TOUCH.
IT WILL NOT MELT ANY OF THE PLASTIC
PARTS OF THE LENS ASSEMBLY.
STRAP THE WATERPROOF
0.150"
POWER MODULE TO THE BODY
OF THE VEHICLE AWAY FROM
0.980"
ANY HIGH HEAT SOURCES.
1.50"
FOR DUAL WALL REFLECTORS: FIRST USE A 1.5" HOLE SAW TO DRILL THROUGH OUTER
LAYER ONLY. THEN USE 1" HOLE SAW TO DRILL THROUGH INNER LAYER USING SAME
0.59"
PILOT DRILL HOLE. INSTALL THE LED HEAD THROUGH THE 1.5" HOLE AND SEAL THE GAP
WITH RTV SILICONE.
The wiring diagram on page 2 shows a typical install.
RED: +V
Connect to +V through an ON/OFF switch.
The use of a fuse located close to the voltage source is recommended.
Size the fuse according to the number of heads used in the system.
18AWG or larger wire is recommended.
BLACK: - GROUND
Connect to - GROUND vehicle chassis.
18AWG or larger wire is recommended.
BLUE: Flash pattern SYNC and SELECTION wire.
If you wish to have all the LED heads synchronize
their flash timings and patterns with each other then all the BLUE wires
must be connected together(64 Heads Maximum).
The BLUE wire is also used to select the flash pattern.
Touch the BLUE wire to +V to select the next pattern in the FLASH
PATTERN LIST. The BLUE wire can also be run to a momentary
push-button located on the dashboard to allow the flash pattern to be
changed when desired.
Note: Do not connect the BLUE wire to - Ground.
It will disrupt the flash pattern sync signal.
INSTALLATION GUIDE
833 W. Diamond St Boise, Idaho 83705
TEL: 888-844-6682 www.strobe.com
MOUNTING
DO NOT DRILL HOLES THROUGH THE POWER MODULE!
ELECTRICAL CONNECTIONS
7/64" PILOT
HOLES
1" HOLE
SCREWS
TIP: APPLY RTV SILICONE
TO THE SCREWS TO SEAL
THE THREADS.
1
TM
SYNC
PAGE 1
Need help?
Do you have a question about the Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600 and is the answer not in the manual?
Questions and answers