Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ACTi Z76
Summary of Contents for ACTi Z76
- Page 1 Dome Camera Hardware Manual 2020/05/18...
-
Page 2: Table Of Contents
Waterproof the RJ-45 Connector Using the Cable Gland ..............18 Access the Camera Configure the IP Addresses ............21 Using DHCP Server to Assign IP Addresses ........ 21 Using the Default Camera IP Address .......... 22 Access the Camera ................. 24 www.acti.com... -
Page 3: Precautions
Every reasonable care has been taken during the writing of this manual. Please inform your local office if you find any inaccuracies or omissions. ACTi will not be held responsible for any typographical or technical errors and reserves the right to make changes to the product and manuals without prior notice. -
Page 4: Regulatory Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. www.acti.com... - Page 5 (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. www.acti.com...
-
Page 6: Safety And Compliance Information
Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. www.acti.com... - Page 7 If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. www.acti.com...
- Page 8 If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) www.acti.com...
-
Page 9: Introduction
Hardware Manual Introduction List of Models This hardware manual contains the following models: 2MP Outdoor Zoom Dome with D/N, Adaptive IR, Basic WDR, Superior Low Light Sensitivity, Fixed Lens www.acti.com... -
Page 10: Package Contents
DO NOT remove this film. It is used to protect the lens cover from scratches or fingerprint marks which may happen during installation. Remove this film only after the camera is securely installed and all connections are complete. www.acti.com... -
Page 11: Physical Description
DC 12V Power Input This connector is used to connect to a DC 12V power Jack adapter if a non-PoE network connection will be used. Ethernet Port Connects to a network using an Ethernet cable. Built-in Microphone Receives audio input. www.acti.com... -
Page 12: Installation Procedures
The images on this section are for reference only; actual lens and cables may vary. 1. Locate the positions of the holes; paste the drill template stickers on the ceiling and drill according to the images below. Cables Going Through the Ceiling Cables Going Along the Ceiling 2. Insert the plastic anchors. www.acti.com... - Page 13 3. Twist the cosmetic ring of the camera. 4. Route the cables through the ceiling (A) or along the ceiling (B). If the cable will be routed along the wall, then cut off the camera tab to where the cable will pass through. www.acti.com...
- Page 14 Hardware Manual 5. Secure the ground screw. 6. Connect the cables. See ** for the detailed description on how to waterproof the Ethernet cable. www.acti.com...
- Page 15 NOTE: If the DC12V connector will not be used, wrap it also in waterproof tape to avoid short circuiting the connector. 8. Mount the camera to the ceiling using the three (3) bundled screws. www.acti.com...
- Page 16 21). Then, adjust the camera tilt and rotation, as needed. 10. To pan the camera, loosen the set screw using the bundled wrench. Then, rotate the camera body. 11. Tighten the screw to fix the camera position. www.acti.com...
- Page 17 Hardware Manual 12. Attach the cosmetic ring to complete the installation. www.acti.com...
-
Page 18: Waterproof The Rj-45 Connector
Use the bundled cable gland to protect the Ethernet connection and use a waterproof tape to protect other cable connections. DISCLAIMER: ACTi will not be responsible for camera damage caused by water entering the cable connections. Using the Cable Gland This section describes how to waterproof the cable-out or “pigtail”... - Page 19 Hardware Manual 3. Insert the clamping nut into the Ethernet cable. 4. Insert the sealing insert through the Ethernet cable. 5. Insert the cable through the gland body. 6. Push the sealing insert into the gland body. www.acti.com...
- Page 20 8. Attach the gland body to the camera connector. 9. Attach the clamping nut to the gland body to complete the cable solution. NOTE: Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly. www.acti.com...
-
Page 21: Access The Camera
The IP Utility can be downloaded for free from http://www.acti.com/IP_Utility With just one click, you can launch the IP Utility and there will be an instant report as follows: You can quickly see the camera model in the list. Double-click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already. -
Page 22: Using The Default Camera Ip Address
PC has to be configured to match the network segment of the camera. Manually adjust the IP address of the PC: In the following example, based on Windows 7, we will configure the IP address to 192.168.0.99 and set Subnet Mask to 255.255.255.0 by using the steps below: www.acti.com... - Page 23 In such case, please plug in only one camera at a time, and change its IP address by using the Web browser before plugging in the next one. This way, the Web browser will not be confused about two devices having the same IP address at the same time. www.acti.com...
-
Page 24: Access The Camera
The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80, which can be omitted from the address for convenience. Before logging in, you need to setup the administrator Password of the camera. www.acti.com... - Page 25 Hardware Manual Then use this newly setup admin account Password to login to the web interface. www.acti.com...
- Page 26 Copyright © 2020, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.com...
Need help?
Do you have a question about the Z76 and is the answer not in the manual?
Questions and answers