Table of Contents
Advertisement
Quick Links
MODEL W1713
16" SCROLL SAW
OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 6/03)
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © AUGUST, 2003 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC., REVISED MAY, 2010 (BL)
226002
#5358DS Printed in China
Advertisement
Table of Contents
Related Manuals for Woodstock W1713
Summary of Contents for Woodstock W1713
- Page 1 Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © AUGUST, 2003 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC., REVISED MAY, 2010 (BL) 226002 #5358DS Printed in China...
-
Page 3: Table Of Contents
INTRODUCTION ...2 Woodstock Technical Support ... 2 About Your New Scroll Saw ... 2 Specifications ... 2 SAFETY ...4 Standard Machinery Safety ... 4 Additional Safety for Scroll Saws ... 6 ELECTRICAL ...7 110V Operation ... 7 Extension Cords ... 7 Electrical Specifications ... -
Page 4: Introduction
The Model W1713 features variable speed blade control, extra large working table, and cast iron construction. This Scroll Saw also offers a gooseneck work lamp, an air nozzle, a dust port, a 45°... -
Page 5: Controls And Features
W1713 Owner's Manual (Mfg. Since 6/03) Controls and Features A. Blade Tension Knob B. Blade Adapters C. Work Lamp D. Blade Guard Work Table Table Insert G. Variable Speed/Power Knob H. Light ON/OFF Button Dust Port 1 Table Tilt Lock Knob K. -
Page 6: Safety
W1713 Owner's Manual (Mfg. Since 6/03) Standard SAFETY Machinery Safety... - Page 7 W1713 Owner's Manual (Mfg. Since 6/03)
-
Page 8: Additional Safety For Scroll Saws
Always wait for the blade to come to full speed before moving the workpiece into W1713 Owner's Manual (Mfg. Since 6/03) USE this and other machinery with caution and respect. -
Page 9: Electrical
"Test Run" portion of this manual. 110V Operation The Model W1713 is wired for 110V operation. The power supply circuit used for this machine MUST be grounded and rated for the amperage given below. Never replace... -
Page 10: Setup
Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1713. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. -
Page 11: Machine Placement
W1713 Owner's Manual (Mfg. Since 6/03) Machine Placement • Workbench Load: This machine distributes a heavy load in a small footprint. Some workbenches may require additional bracing to support both machine and operator. • Working Clearances: Consider existing and anticipated needs, size of material to be... -
Page 12: Assembly
3. Pivot the guard up-and-down to ensure that it moves smoothly. If necessary, loosen the mounting screw until the movement is smooth. W1713 Owner's Manual (Mfg. Since 6/03) Keep machine disconnected from power until instructed otherwise. Mounting Screw Figure 4. -
Page 13: Installing Pin-End Blades
W1713 Owner's Manual (Mfg. Since 6/03) Installing Pin-End Blades Scroll saw blades are classified as either "pin-end" (mounting pins in the ends of the blade) or "plain end" (no pins). The blades included with your scroll saw are pin- end blades. -
Page 14: Installing Plain End Blades
9. Replace the table insert, then properly tension the blade (refer to Adjusting Blade Tension on Page 17 for detailed instructions). W1713 Owner's Manual (Mfg. Since 6/03) Screw Figure 7. Plain end blade inserted and secured into a blade adapter. -
Page 15: Calibrating Table Tilt Scale
W1713 Owner's Manual (Mfg. Since 6/03) Calibrating Table Tilt Scale The table lock knob and tilt scale are used to tilt the table for horizontal angle cuts. Note: The table tilt scale is only an approximate scale and should not be used when precise angle measurements are required for the operation. -
Page 16: Test Run
Always disconnect the machine from power when investigating or correcting potential problems. 7. Turn the machine OFF. W1713 Owner's Manual (Mfg. Since 6/03) Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses to reduce the risk of injury. -
Page 17: Operations
W1713 Owner's Manual (Mfg. Since 6/03) General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine. -
Page 18: Adjusting Hold-Down Shoe & Blade Guard
Use the air nozzle screw shown in Figure 12 to adjust the position of the nozzle that best suits your operation. W1713 Owner's Manual (Mfg. Since 6/03) Lock Knob Air Nozzle... -
Page 19: Adjusting Blade Tension
W1713 Owner's Manual (Mfg. Since 6/03) Adjusting Blade Tension Having proper blade tension is critical to safe cutting operations that produce good results. Blades that are tensioned correctly will also last longer and are less likely to break during the cutting operation. However, finding the correct amount of tension for each type of blade is matter of trial-and-error and experience. -
Page 20: Blade Speed
Thickness 10 TPI 0.110" 15 TPI 0.110" 18 TPI 0.095" W1713 Owner's Manual (Mfg. Since 6/03) Figure 14. Variable speed/power knob. Workpiece Material 0.020" 1200–1650 General purpose blade for cutting hard and soft woods between plastics, paper, felt, and bone. -
Page 21: Standard Scroll Cutting
W1713 Owner's Manual (Mfg. Since 6/03) Standard Scroll Cutting For standard scroll cutting, follow the pattern line on the workpiece by pushing and turning the workpiece at the same time, which allows the kerf of the cut to make way for the turn. -
Page 22: Maintenance
SLIPIT . For long term storage you may ® want to consider products like Boeshield T-9™. W1713 Owner's Manual (Mfg. Since 6/03) MAKE SURE that your machine is unplugged during all maintenance pro- cedures! If this warning is ignored, seri- ous personal injury may occur. -
Page 23: Lubrication
W1713 Owner's Manual (Mfg. Since 6/03) Lubrication The motor bearings are lubricated and sealed at the factory. Merely leave them alone unless they need to be replaced. The upper and lower arms have two bushings each that require lubrication after every 8 hours of machine use. -
Page 24: Service
This section covers the most common problems and corrections with this type of machine. If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz. WARNING! DO NOT make any... -
Page 25: Parts
W1713 Owner's Manual (Mfg. Since 6/03) PARTS Main -23-... -
Page 26: Main Parts List
BUSHING 3/8" X1713046 MOTOR 1/8HP 110V 60HZ 46-1 X1713046-1 CARBON BRUSH 46-2 X1713046-2 CARBON BRUSH CAP X1713047 FLYWHEEL X1713048 BEARING HOUSING W1713 Owner's Manual (Mfg. Since 6/03) Main Parts List PART # XP625ZZ X1713050 XPCAP24M XPLW01M XPCAP38M XPW02M X1713056 XPN06M... -
Page 27: Machine Labels
MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www.shopfoxtools.com to order new labels. - Page 28 W1713 Owner's Manual (Mfg. Since 6/03) Notes -26-...
- Page 29 W1713 Owner's Manual (Mfg. Since 6/03)
- Page 30 FOLD ALONG DOTTED LINE Place Stamp Here FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
-
Page 31: Warranty
WARRANTY...