Rinnai Brivis Contour Series Operation Manual
Rinnai Brivis Contour Series Operation Manual

Rinnai Brivis Contour Series Operation Manual

Evaporative air coolers
Table of Contents

Advertisement

Brivis Models:
Contour Series
Promina Series
Advance Series
AD Series
Evaporative Air Coolers
Operation Manual
by

Advertisement

Table of Contents
loading

Summary of Contents for Rinnai Brivis Contour Series

  • Page 1 Brivis Models: Contour Series Promina Series Advance Series AD Series Evaporative Air Coolers Operation Manual...
  • Page 2 This appliance must be installed in accordance with: • Manufacturer’s Installation Instructions • Current AS/NZS 3000 • Local Regulations and Municipal Building Codes including local OH&S requirements This appliance must be installed, maintained and removed only by an Authorised Person. For continued safety of this appliance it must be installed and maintained in accordance with the manufacturer’s instructions.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS Warnings and Important Information Regulatory / Installation / Safety �������������������������������������������������������������������������������������������������������������������������������������������� 5 Models Covered In This Manual �������������������������������������������������������������������������������������������������������������������������������������������� 5 Clearances Roof Mounted Evaporative Cooler Positioning ���������������������������������������������������������������������������������������������������������������������� 6 Mandatory Inspection prior to Installation ������������������������������������������������������������������������������������������������������������������������������ 6 Evaporative Cooler Operation Introduction ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 7 How Does Your Evaporative Cooling Work? �������������������������������������������������������������������������������������������������������������������������...
  • Page 4 TABLE OF CONTENTS Zoning ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 15 Dual Brivis Networker Operation ����������������������������������������������������������������������������������������������������������������������������������������� 15 Batteries ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 15 Programmable Control Operation Operating Your Programmable Wall Control ������������������������������������������������������������������������������������������������������������������������ 16 Automatic Pre-Wet ��������������������������������������������������������������������������������������������������������������������������������������������������������������� 16 Operating Modes ����������������������������������������������������������������������������������������������������������������������������������������������������������������� 16 Auto Operation ��������������������������������������������������������������������������������������������������������������������������������������������������������������������� 16 Getting Started ��������������������������������������������������������������������������������������������������������������������������������������������������������������������� 16 Benefits of Using in AUTO Mode in Preference to Manual Mode ����������������������������������������������������������������������������������������...
  • Page 5: Warnings And Important Information

    SHOULD: INDICATES A RECOMMENDED REQUIREMENT OF THIS MANUAL. Any deviations from these instructions may, at the discretion of Rinnai, void the warranty. As a result, the customer and/or installer may be charged a fee for product non-warranty related call outs. Also, note that failure to comply with these instructions may preclude Rinnai from being able to service the unit.
  • Page 6: Clearances

    For safety and warranty purposes, appliances that may be damaged or incorrect must not be installed or operated under any circumstances� Installation of damaged or incorrect appliances may contravene local government regulations� Rinnai disclaims any liability or responsibility whatsoever in relation to the installation or operation of damaged or incorrect appliances�...
  • Page 7: Evaporative Cooler Operation

    EVAPORATIVE COOLER OPERATION INTRODUCTION Congratulations on your purchase of a Brivis Cooling system. For you to achieve the performance and efficiency expected from your new cooler, please ensure the installer is a qualified trades person, that the installer has commissioned the unit before you commence operating, and you take the time to read the contents of this manual. In some Australian States it is mandatory that your cooler installation is issued with a certificate of compliance to guarantee the installation workmanship�...
  • Page 8: The Air Smells A Little Different, Why

    Most models have pre-programmed function times, to allow time to fill the Cooler’s tank with water and/or Pre-wet the filter pads. Brivis Contour Series models have an additional delay to allow time to open the ServoSeal damper. The entire process can take up to 8 minutes before cool air is expected from the duct outlets.
  • Page 9: Networker Wall Control Operation

    NETWORKER WALL CONTROL OPERATION ABOUT YOUR BRIVIS NETWORKER WALL CONTROL The Brivis Networker wall control operates the complete cooling system, communicating key information and sensing the temperature. It is an important part of the unit and the following text will explain its operation. 8 - (14,15,16,17,18) 1�...
  • Page 10: Automatic Pre-Wet

    NETWORKER WALL CONTROL OPERATION AUTOMATIC PRE-WET When the Cooler is turned ON, with both the fan and the pump in either Auto or Manual mode, the Cooler will start a Pre-Wet automatically� The Pre-Wet stage ensures the pads are thoroughly wet before the fan starts� This prevents warm air being initially blown into your home and contributes to the effective operation and performance of the Cooler.
  • Page 11: Manual Operation

    NETWORKER WALL CONTROL OPERATION MANUAL OPERATION Manual operation enables you to control the fan, its speed, and the pump manually. To run the Cooler in Manual mode, just follow these steps: 1� Turn the Brivis Networker on using the ON/OFF button (1)� 2�...
  • Page 12: Setting The Time & Day

    NETWORKER WALL CONTROL OPERATION If the pump is going to be used, adequate ventilation (openings) need to be provided to prevent condensation build up. CAUTION SETTING THE TIME & DAY 1� Ensure the Networker is turned OFF using the ON/OFF button (1)� 2�...
  • Page 13: Coded Messages

    NETWORKER WALL CONTROL OPERATION Press either the ON/OFF button (1) or the PROG button (5)� The Brivis Networker remembers the last setting and the next time you select the Timer it will go to that same setting. CODED MESSAGES While the Brivis Networker is operating your system, it is also monitoring and controlling every aspect of the system's performance.
  • Page 14: Locking The Brivis Networker

    NETWORKER WALL CONTROL OPERATION LOCKING THE BRIVIS NETWORKER To prevent any unwanted alterations being made to the coolers settings, the Brivis Networker can be locked via a 4- digit PIN code. In the case of dual Brivis Networkers, if one is locked the other is also locked. If dual Brivis Networkers are installed, the user PIN codes can only be set at the Master Brivis Networker.
  • Page 15: Zoning

    NETWORKER WALL CONTROL OPERATION ZONING Some systems may include multiple Coolers with each operating in a different zone area. Zone keys (28) will appear on the screen and these will have been set up and explained by the installer where required. These zones can be operated in either “Manual”...
  • Page 16: Programmable Control Operation

    PROGRAMMABLE CONTROL OPERATION OPERATING YOUR PROGRAMMABLE WALL CONTROL This Wall Control gives the choice of Automatic or Manual modes with the option of a time ON or OFF delay� AUTOMATIC PRE-WET When the cooler is turned on with both the fan and the pump, in either Auto or Manual mode, the cooler will start a Pre-Wet stage to ensure the pads are thoroughly wet before the fan starts.
  • Page 17: Manual Operation

    PROGRAMMABLE CONTROL OPERATION MANUAL OPERATION Manual operation requires you to manually control the fan, its speed, and the pump. GETTING STARTED Begin by pressing the ON/OFF key to turn the Cooler on� For Manual operation the AUTO light must not be illuminated�...
  • Page 18: Manual Wall Control Operation

    MANUAL WALL CONTROL OPERATION OPERATING YOUR MANUAL WALL CONTROL The Manual Wall Control requires you to manually control Pump (and Pre-Wet cycle) operations, fan operation and the fan speed� On days of high humidity for ventilation the fan may be operated without operating the pump� To run the Cooler 1�...
  • Page 19: Care & Maintenance

    Check that the fan is not in Time Delay Mode caused by: pre-programmed times The usual time for the ServoSeal damper (Brivis Contour Series only) and motorised drain to delay can be up open, the Cooler’s tank to fill with water, or a pre-wet of the filter pads.
  • Page 20: Installation Record

    CARE & MAINTENANCE The unit is not cooling very well • Check the water supply tap is turned on at the Cooler • Check the pump has been selected on the wall control� • Check sufficient door and/or windows have been opened. Refer to exhaust requirements covered in "Before Operating Your Evaporative Cooler"...
  • Page 21: Faq

    CARE & MAINTENANCE SERVICE MAINTENANCE SCHEDULE Your ducted evaporative cooler should be serviced at two-year intervals after the date of installation by a qualified licensed technician in accordance with the Schedule below� Failure to do so during the product warranty period may void your warranty.
  • Page 22 Check and lubricate all moving parts� • On Brivis Contour Series and some Advance Series models, ensure the ServoSeal damper mechanism is opening and closing correctly� Please note that to maintain your warranty, the above servicing needs to be conducted by an authorised person trained in the service of Brivis Coolers.
  • Page 23 This means you will see the unit dump the water out of the overflow pipe. Brivis Contour Series models will not dump any water during operation as they are fitted with an AquaSave which operates to keep the water clean�...
  • Page 24 Your evaporative cooler has lost communication with your Networker wall controller, a service call is required. We have a unit with a Brivis Networker Wall Controller� How is the LED screen backlight activated without changing any setting? Is there one key to press that activates the backlight without affecting the current controller function? The LED backlit screen can be activated by pressing the Function key (Fn button)�...
  • Page 25: Warranty

    WARRANTY TERMS OF WARRANTY – AUSTRALIA Rinnai Australia Pty. Ltd. ABN 74 005 138 769, 100 Atlantic Drive, Keysborough VIC 3173. NOTICE TO CONSUMERS UNDER AUSTRALIAN CONSUMER LAW Our goods and services come with guarantees that cannot be excluded under the Australian Consumer Law.
  • Page 26 Normal Business Hours by an Authorised Service Representative� Repair by persons other than an Authorised Service Representatives may void the Warranty� 2�4 Alternatively to clause 2.3 above, Rinnai can at its discretion elect to pay you an amount equivalent to the cost of repairing or replacing the Product�...
  • Page 27 "7 Purchaser’s Responsibilities" on page 28; c) notifies Rinnai within 30 days of a defect occurring or, in the case of a latent defect, becoming apparent, that a claim is being made under this Warranty; and d) provides, in support of the claim made under this Warranty, a Proof of Purchase.
  • Page 28 Rinnai to enquire about alternative arrangements. If you wish to make a warranty claim in respect of any fixed Product, please contact Rinnai on the details set out below to make arrangements for an Authorised Service Representative to inspect the product�...
  • Page 29 NOTES Brivis Evap AC OM...
  • Page 30 NOTES Brivis Evap AC OM...
  • Page 31 NOTES Brivis Evap AC OM...
  • Page 32 Tel: 1300 555 545* Fax: 1300 555 655 Monday to Friday, 8.00 am to 5.00 pm EST. *Cost of a local call higher from mobile or public phones. For further information visit www.rinnai.com.au or email enquiry@rinnai.com.au innai has a Service and Spare Parts network with...

Table of Contents