Table of Contents
Advertisement
• You must select a location that is strong enough to support
the weight of the device and protect it from excessive
vibration or shock.
• You should select a location that allows for easy access to all
device interfaces, such as the keypad, touchscreen, and card
reader, if applicable.
• To avoid interference with a magnetic compass, you must not
mount the device closer to a compass than the compass-safe
distance value listed in the product specifications.
• You must select a location that allows room for the routing
and connection of all cables.
• If the mounting location for a GPSMAP 8x22 or GPSMAP
8x24 chartplotter is in direct sunlight and in a horizontal
orientation, ensure that the installation location meets as
many of the following criteria as possible:
◦ Sufficient air flow
◦ Proper ventilation
◦ Cooling source on the front and rear of the chartplotter
◦ Method to shade the display using a canopy, window tint,
or shroud
NOTE: If possible, you should meet all of these criteria to
prevent this issue when installing a GPSMAP 8x22 or
GPSMAP 8x24 chartplotter.
Mounting the Device
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
To avoid potential damage to the powder coating, use only the
included screws to mount the device. Using screws other than
the ones included will void your warranty.
Do not remove the blue, rubber protective bumper until after the
installation is complete. The bumper helps protect the device
from damage during installation.
The included template and hardware can be used to flush mount
the device in your dashboard. There are three options for
hardware based on the mounting surface material.
• You can drill pilot holes and use the included wood screws.
• You can drill holes and use the included nut plates and
machine screws. The nut plates can add stability to a thinner
surface.
• You can punch holes, tap them to M4, and use the included
machine screws.
1
Trim the template and make sure it fits in the location where
you want to mount the device.
2
Secure the template to the selected location.
9
3
Using a 3.6 mm (
/
in.) drill bit, drill one or more of the holes
64
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4
Using a jigsaw or rotary tool, cut the mounting surface along
the inside of the solid line indicated on the template.
5
Place the device in the cutout to test the fit.
6
If necessary, use a file and sandpaper to refine the size of
the cutout.
7
After the device fits correctly in the cutout, ensure the
mounting holes on the device line up with the larger 7.2 mm
9
(
/
in.) holes on the template.
32
8
If the mounting holes on the device do not line up, mark the
new hole locations.
9
Based on your mounting surface, drill or punch and tap the
larger holes:
2
NOTICE
1
• Drill 3.2 mm (
/
in.) pilot holes for the included wood
8
screws, and skip to step 18.
9
• Drill 7.2 mm (
/
in.) holes for the included nut plate and
32
machine screws.
• Punch and tap M4 holes for the included machine screws,
and skip to step 18.
10
If using the nut plates, starting in one corner of the template,
place a nut plate
over the larger hole
The smaller hole
on the nut plate should line up with the
smaller hole on the template.
9
11
If the smaller 3.6 mm (
line up with the smaller hole on the template, mark the new
location.
12
Repeat steps 10 and 11 for each nut plate.
13
9
Using a 3.6 mm (
/
in.) drill bit, drill the smaller holes.
64
14
Remove the template from the mounting surface.
15
Starting in one corner of the mounting location, place a nut
plate
on the back of the mounting surface, lining up the
large and small holes.
The raised portion of the nut plate should fit into the larger
hole.
16
Secure the nut plate to the mounting surface by fastening an
included M3 screw
through the smaller 3.6 mm (
hole.
17
Repeat steps 15 and 16 for each of the nut plates along the
top and bottom of the device.
18
If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
NOTE: To prevent corrosion of the metal contacts, cover
unused connectors with the attached weather caps.
19
Place the device into the cutout.
20
Secure the device to the mounting surface using the included
M4 screws
or wood screws, depending on the mounting
method.
21
Carefully remove and discard the rubber protective bumper.
22
Install the decorative bezel by snapping it in place around the
edges of the device.
drilled in step 9.
/
in.) hole on the nut plate does not
64
9
/
in.)
64
Advertisement
Table of Contents
