Advertisement
DTP2 R 212 Series • Setup Guide (Continued)
B
DTP2 input 2
(see
figure 1
RJ-45 and this connector (see
ATTENTION:
•
Do NOT use the receiver to remotely power a legacy DTP unit. Circuit damage to the transmitter WILL result.
•
NE PAS utiliser le récepteur pour alimenter à distance un émetteur de la gamme existante DTP. Cette opération
FINIRA par endommager le circuit menant à l'émetteur.
Signal LED indicator — Lights green when the receiver accepts a video signal.
Link LED indicator — Lights yellow when a device is connected and communication is established.
C
Over DTP2 RS-232 and IR port
into this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232 and IR communication (see
connectors
on page 6 to wire the connector). RS-232 and IR data can be transmitted simultaneously.
D
HDMI output port
— Connect an HDMI cable between this port and an HDMI video display. See
page 7 to use the LockIt HDMI Cable Lacing Bracket to secure the connector to the switcher.
NOTE:
The maximum HDMI cable length is 4.5 m (15 feet).
E
Audio output port
— Connect an audio device such as an audio amplifier or powered speakers to this 5-pole, 3.5 mm
captive screw connector. This connector outputs unamplified, line level audio, whether it is from an analog input to the
transmitter or de-embedded from the transmitter HDMI input (see
connectors).
This connector can be tied to the amplified output (SA models) so that the volume varies as the amplified output varies or fixed at
0 dB.
F
Amplified output
(DTP2 R 212 SA only) — Connect unpowered, 4-ohm or 8-ohm speakers to this 4-pole 5 mm
captive screw connector to play the amplified stereo audio output.
G
Display RS-232 port
connector for control of a connected display device via the DTP transmitter. (see
wire the connector)
H
Volume port
(DTP2 R 212 SA only) — The volume of the amplified audio output can be controlled via a hard-wired
potentiometer control, such as the Extron VC 50, the VCM 100 Series devices, and the VCM 200 Series devices. A locally-
constructed device can also be used (see the DTP2 R 212 User Guide for assembly guidelines).
NOTE:
The Volume switch (
control the volume.
I
Volume switch
(DTP2 R 212 SA only) — Set this switch as follows to select how the amplified output volume is controlled.
RS-232 position (up) — The volume of the amplified audio output can be controlled via the RS-232 port by issuing SIS
commands or the Product Configuration Software.
Volume port position (down) — The volume of the amplified audio output can be controlled via a local control device
connected to the Volume port (H).
J
Remote RS-232 port
remote control of the switcher (see
K
LAN port
— If desired, for remote control of the networked switcher, connect the switcher to a PC or to an Ethernet LAN via
this RJ-45 connector.
Act (yellow) LED — The Act LED indicates transmission of data packets on the RJ-45 connector. This LED blinks as the
switcher communicates.
Link (green) LED — The Link LED indicates that the switcher is properly connected to an Ethernet LAN. This LED lights steadily.
L
Power connector and LED
2
on page 1) — Connect an STP cable between a compatible Extron DTP transmitting device
TP connectors
on page 8 to properly wire the connector and for detailed NOTES).
(input 2) — Plug a serial RS-232 signal, a modulated IR signal (up to 40 kHz), or both
— If desired, connect serial bidirectional RS-232 signals to this 3.5 mm, 5-pole captive screw
) must be in the Volume Port (down) position for a device connected to this port to
I
— Plug a serial RS-232 device into the switcher via this 3.5 mm, 3-pole captive screw connector for
RS-232 and IR connectors
— Plug the included external 12 VDC power supply into this 2-pole connector.
Analog audio output connector
RS-232 and IR connectors
on page 6 to wire the connector).
SIG
DTP2 IN
OVER DTP2
2
RS-232
RS-232 and IR
Tx
Rx
HDMI connectors
on
on page 10 to wire the
4/8 OHM
L
on page 6 to
LINK
IR
G
Tx
Rx
L
R
CLASS
WIRING
R
DISPLAY
RS-232
Tx Rx G
10V
50mA
V
C G
VOL
RS-232
Tx
Rx
G
LAN
POWER
12V
2.0 A MAX
Advertisement
