Table of Contents
Advertisement
Turning Off the Varia RDU Device and Radar
Device
If the Varia RDU device is paired with the radar device, you can
turn off both devices at the same time.
Hold the device key on the Varia RDU device for 1 second.
Other Compatible Devices
Pairing the Radar Device with a Compatible
Edge Device
This task is for the Edge 1000, 830, 530, and 130 devices. If
your device is not listed, go to buy.garmin.com.
1
Bring the Edge device within range (3 m) of the sensor.
NOTE: Stay 10 m away from other ANT+ sensors while
pairing.
2
Turn on the Edge device.
3
From the Sensors menu, select Add Sensor > Search All.
4
While the Varia RVR315 device is turned off, hold the device
key for 1 second to enter active mode.
The status LED flashes blue, and the radar device turns on.
5
Select your sensor.
When the sensor is paired with your Edge device, the radar
status icon appears solid.
Pairing the Radar Device with a Compatible
Garmin Watch
This task is for the Forerunner
vívoactive
4 series watches. If your device is not listed, go to
®
buy.garmin.com.
1
Bring the watch within range (3 m) of the sensor.
NOTE: Stay 10 m away from other ANT+ sensors while
pairing.
2
Turn on the Garmin watch.
3
From the Settings menu, select Sensors > Add New >
Search All.
4
While the Varia RVR315 device is turned off, hold the device
key for 1 second to enter active mode.
The status LED flashes blue, and the radar device turns on.
5
Select your sensor.
When the sensor is paired with your Garmin watch, the radar
status icon appears solid.
Device Information
Charging the Device
To prevent corrosion, thoroughly dry the USB port, the weather
cap, and the surrounding area before charging or connecting to
a computer.
The device is powered by a built-in lithium-ion battery that you
can charge using a standard wall outlet or a USB port on your
computer.
NOTE: The device does not charge when outside the approved
temperature range
(Varia RVR315 Specifications, page
1
Pull up the weather cap
4
945, fēnix
6 series, and
®
®
NOTICE
from the USB port
.
2
Plug the small end of the USB cable into the USB port on the
device.
3
Plug the large end of the USB cable into an AC adapter or a
computer USB port.
4
Plug the AC adapter into a standard wall outlet.
5
Charge the device completely.
The status LED flashes green while charging. The status
LED is solid green when charging is complete.
6
Remove the USB cable, and close the weather cap.
Tips for Charging the Device
• Connect the charger securely to the device.
You can charge the device by plugging the USB cable into a
Garmin approved AC adapter with a standard wall outlet or a
USB port on your computer. Charging a fully depleted battery
takes about 5 hours using a computer and 3 hours using an
AC power source.
• Remove the charger from the device when the status LED is
solid green.
• View the remaining battery life
settings widget
Device Care
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Avoid chemical cleaners, solvents, and insect repellents that can
damage plastic components and finishes.
Secure the weather cap tightly to prevent damage to the USB
port.
Avoid extreme shock and harsh treatment, because it can
degrade the life of the product.
Cleaning the Device
• Clear mud and dirt from the weather cap area.
• While the weather cap is closed, hold the device under
running water.
After cleaning, allow the device to dry completely.
Radar Detection
5).
• The radar detects approaching vehicles up to 140 m away.
• The approaching vehicle speed must be from 10 to 160 km/h
(from 6 to 99 mph).
NOTE: The radar does not detect vehicles traveling at the
same speed as your bike.
on your Edge 1030
(Viewing Edge Widgets, page
NOTICE
Other Compatible Devices
2).
Advertisement
Table of Contents
