Configuration Menu; Buttons And Switches; The Display; Operation - White Rodgers 1F83-277 User Manual

Before you begin programming your thermostat, you should be
familiar with its features and with the display and the location
and operation of the thermostat buttons. Your thermostat
consists of two parts: the thermostat cover and the base. To
remove the cover, pull it straight out from the base. To replace
the cover, line up the cover with the base and press until the
cover snaps onto the base.
The Thermostat Buttons and Switches The Thermostat Buttons and Switches
The Thermostat Buttons and Switches The Thermostat Buttons and Switches The Thermostat Buttons and Switches
Raises temperature setting
1
Lowers temperature setting.
2
ON ON AUTO AUTO
FAN switch (ON ON, AUTO ON AUTO) AUTO
3
SYSTEM button (COOL COOL, AUTO COOL COOL
4 COOL

The Display

The Display The Display
The Display The Display
Flame icon ( ) is displayed when the system is in Flame icon Flame icon
5 Flame icon Flame icon
HEAT HEAT Snowflake icon Snowflake icon
HEAT HEAT HEAT mode. Snowflake icon Snowflake icon ( ) is displayed when Snowflake icon
the system is in COOL COOL COOL mode. Flame icon COOL COOL
Snowflake icon Snowflake icon Snowflake icon Snowflake icon Snowflake icon ( ) are displayed simultaneously
when thermostat is in AUTO
Displays BATT BATT BATT when the 2 "AA" batteries are low and BATT BATT
6
should be replaced. Only BATT
when batteries are low with no system power.
Displays current temperature or LO
7
are low.
Displays currently programmed set temperature (this
8
is blank when SYSTEM is OFF).
Displays FLTR FLTR FLTR FLTR when the system has run for the
9 FLTR
programmed filter time period as a reminder to change
or clean your filter.
Display ( ) when in keypad lockout mode.
10
The configuration menu allows you to set certain thermostat
operating characteristics to your system or personal require-
ments.
Set SYSTEM SYSTEM SYSTEM SYSTEM button to OFF SYSTEM
and to enter configuration menu. The display will
show the first item in the configuration menu.
The configuration menu table summarizes the configuration
options. An explanation of each option follows.
Press SYSTEM SYSTEM SYSTEM to change to the next menu item. To exit the SYSTEM SYSTEM
menu and return to the program operation, press RUN
keys are pressed within fifteen minutes, the thermostat will
revert to normal operation.
1) Single Stage, Multi-stage or Heat Pump System Single Stage, Multi-stage or Heat Pump System Single Stage, Multi-stage or Heat Pump System Single Stage, Multi-stage or Heat Pump System Single Stage, Multi-stage or Heat Pump System
Configuration – This control can be configured for Heat Configuration Configuration Configuration Configuration
Pump or two stage heat/two stage cool multi-stage opera-
tion. The display indicates MS 2
mode) in the display. The Multi-stage configuration can be
SS1 SS1 HP2 HP2
toggled to SS1 SS1 SS1, HP2 HP2 HP2, or HP1
ture Up ture Up ture Up ture Up ture Up or Temperature Down Temperature Down key. In Multi-stage configu- Temperature Down Temperature Down Temperature Down
ration, system button will not have EMER
AUTO AUTO AUTO, HEAT HEAT HEAT, EMER HEAT EMER EMER EMER, OFF OFF OFF) OFF
AUTO HEAT EMER OFF
Flame icon Flame icon Flame icon ( ) and Flame icon
AUTO AUTO mode. AUTO
AUTO
BATT BATT BATT and LO BATT LO LO LO LO are displayed
LO when batteries LO LO
LO
OFF OFF OFF OFF, then simultaneously press
RUN RUN RUN. If no RUN
MS 2 (default for multi-stage MS 2 MS 2
MS 2
HP1 HP1 Tempera- Tempera-
HP1 HP1 by pressing the Tempera- Tempera- Tempera-
EMER EMERgency mode. EMER EMER
STG1+2
EMER
Figure 6 – Thermostat display, buttons and switches Figure 6 – Thermostat display, buttons and switches Figure 6 – Thermostat display, buttons and switches Figure 6 – Thermostat display, buttons and switches Figure 6 – Thermostat display, buttons and switches
EMER is displayed flashing when the system is in EMER EMER EMER EMER
11
EMER mode.
Indicates a fault in the heating/cooling system. It does
12
not indicate a fault in the thermostat.
Display ( ) when limited range is activated.
13
Stage1 & 2 indicators: The thermostat shall indicate Stage1 & 2 Stage1 & 2
14 Stage1 & 2 Stage1 & 2
when the first and second stage is energized except
in emergency mode. The icon is STG 1
stage energized. The icons for the first and second
stage energized are STG1+2 STG1+2 STG1+2 located in the upper STG1+2 STG1+2
right side of the display.

CONFIGURATION MENU

CONFIGURATION MENU CONFIGURATION MENU
CONFIGURATION MENU CONFIGURATION MENU
2) Fast or Slow Cycle Selection Fast or Slow Cycle Selection – The factory default setting Fast or Slow Cycle Selection Fast or Slow Cycle Selection Fast or Slow Cycle Selection
is fast cycle, which cycles 1st stage at approximately 1.2°F
and 2nd stage 0.75°F. If you prefer slow cycle, press the
temperature key to change to SL. The 1st stage and 2nd
stage would be 1.5°F and 1.2°F respectively.
Select Compressor Lockout CL OFF or ON Select Compressor Lockout CL OFF or ON
3) Select Compressor Lockout CL OFF or ON Select Compressor Lockout CL OFF or ON – Selecting Select Compressor Lockout CL OFF or ON
CL ON will cause the thermostat to wait 5 minutes before
turning on the compressor if the heating and cooling system
loses power. It will also wait 5 minutes minimum between
cooling and heating cycles. This is intended to help protect
the compressor from short cycling. Some newer compres-
sors already have a time delay built in and do not require
this feature. Your compressor manufacturer can tell you if
the lockout feature is already present in their system. When
the thermostat compressor time delay occurs it will flash the
setpoint for about five minutes.

OPERATION

OPERATION
OPERATION OPERATION OPERATION
FAULT
STG 1 for the first STG 1 STG 1 STG 1
5