Advertisement
DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Step 1
Device power off.
Step 2
After lift the device upward slightly, first shift out the
top of DIN-Rail mounting kit, then shift out the
bottom of DIN-Rail, disassembling ends.
Note:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Power Supply Connection】
DC power supply
This series media converter provides 3-pin
industrial terminals (1, 2, 3). 1 is positive pole,
2 is shell ground, 3 is negative pole.
Power Range: 12 ~ 48VDC (POE48VDC).
Note:
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then
remove the power line, please note the operation order
above.
【DIP Switch Setting】
Provide 4-pin DIP switch for function setting,
where "ON" is enable valid terminal. Please
power off and power on after changing the status
of DIP switch. DIP switch 1~4 define as follow:
1. Standard PD / LEGACY PD switching (default is OFF,
the standard PD resistance detection).
2. Jumbo frame enabled.
3. Supports two definitions. Model I and model III: LFP
enabled; model II and model IV: Flow control.
4 Force copper port 100M speed.
【Checking LED Indicator】
The device provides LED indicators to monitor the device
working
status
with
a
comprehensive
troubleshooting; the function of each LED is described in the
table as below:
LED
Status
Description
ON
Copper port link fault alarm.
LFP (TX)
OFF
Copper port link is normal.
ON
Optical fiber port link fault alarm.
LFP (FX)
OFF
Optical fiber port link is normal.
The device is powered on or the
ON
device is abnormal.
RUN
The device is powered off or the
OFF
device is abnormal.
Blinking
System is running well.
POE port for PD device normal
ON
power supply.
POE port is in detection or fault
POE
Blinking
status.
POE port is not connected with
OFF
the PD device.
Port has established a valid
ON
network connection.
G1~G2/G3
Blinking
Port is in network communication.
Port has not established a valid
OFF
network connection.
【Specification】
Panel
Gigabit POE port
10/100/1000 Base-T(X) adaptive,
full-duplex/half-duplex adaptive and
MDI/MDI-X adaptive;
PoE port, the maximum output
power is 30W.
POE pins
Gigabit fiber port
Gigabit SFP slot
Indicator
simplified
Exchange attributes
Backplane bandwidth
Packet buffer size
MAC table size
Power supply
Input power supply
Access terminal
Consumption
IPMC100-1GF-1GPOE No-load: 1.44W@48VDC
IPMC100-1GF-2GPOE No-load: 5.14W@48VDC
IPMC100-1GS-1GPOE No-load: .1.49W@48VDC
IPMC100-1GS-2GPOE No-load: 2.11W@48VDC
Working environment
Working temperature
Storage temperature
Working humidity
Protection grade
V +, V +, V-, V- corresponds to pins
1, 2, 3, 6.
1000 Base-FX, the optical port is a
full duplex SC/ST/FC single mode
or multimode interface.
100/1000 Base-SFP
LFP indicator, run indicator,
interface indicator, POE indicator
14G
1Mbit
8K
12~48VDC (POE48VDC)
3-pin 7.62mm pitch terminal block
Full-load: 28.51W@48VDC
Full-load: 55.30W@48VDC
Full-load: 27.55W@48VDC
Full-load: 53.76W@48VDC
-40℃～80℃
-40℃～85℃
5%～95% (no condensation)
IP40 (metal shell)
Advertisement
