Related Manuals for Flexicon FS32
Summary of Contents for Flexicon FS32
- Page 1 INSTRUCTION HANDBOOK FS10, FS32 FS32 & FS10 (example; exact model may vary) This instruction handbook is for the daily users of the equipment. FS10-32 IH EN 74-310-002 v1.04.doc Version: 1.04 Page 1 of 16...
-
Page 2: Table Of Contents
Essential training before daily use ................... 4 References ..........................4 Dismantling and disposal ......................4 General information ......................... 5 Unpacking and inspection ......................5 Receiving and storing the FS10/FS32 ..................5 Mounting of capping head ....................... 5 Technical specifications ......................6 2.4.1 Dimensions ..........................6 2.4.2... -
Page 3: Introduction
FS10 is designed for crimping 8 mm, 13 mm and 20 mm standard crimp caps* with or without flip-off plastic disc. FS32 is mainly designed for 20mm and 32 mm caps*, also with or without flip-off plastic disc. Crimping is performed by pressing the bottle or vial against the bottle holder. This causes the crimp head to move down onto the bottle, the jaws close around the cap, pressure is applied, the jaws release and the head lifts again. -
Page 4: Caution And Employee Safety
INSTRUCTION HANDBOOK FS10, FS32 1.4 Caution and employee safety This manual should be read before using the FS10/FS32. It is strongly advised that Any kind of maintenance or cleaning of the machine not is carried out while power is connected... -
Page 5: General Information
Before unpacking or storing of the FS10/FS32 it should be checked if the crate is damaged. In case of long-term storage of the FS10/FS32 before installation, the machine must be stored in the crate, and placed in a dry room. The crate is not water resistant. -
Page 6: Technical Specifications
INSTRUCTION HANDBOOK FS10, FS32 2.4 Technical specifications 2.4.1 Dimensions FS10 FS32 FS10-32 IH EN 74-310-002 v1.04.doc Version: 1.04 Page 6 of 16... -
Page 7: Buttons / Connections
INSTRUCTION HANDBOOK FS10, FS32 2.4.2 Buttons / Connections ON/OFF Button / Emergency stop Power indicator; lights when power is on. OFF is used for emergency stopping. Power supply connection Compressed air connection Exhaust filter and air collection Air tubes for the crimp head FS10-32 IH EN 74-310-002 v1.04.doc... -
Page 8: Services
INSTRUCTION HANDBOOK FS10, FS32 2.4.3 Services All electrical systems are placed inside the machine. Power supply: 110/230 VAC earthed, 50/60Hz Consumption: 50 W Compressed air: 0,6 MPa / 6 bar, clean and dry air 35 L/min. free air Consumption, FS10: 50 L/min. -
Page 9: Installation
INSTRUCTION HANDBOOK FS10, FS32 3 Installation 3.1 Connections FS10 / FS32 must be placed on a stable and horizontal bedplate. The mains cable (1) is connected to a single- phase power supply with earth. The plug box (1) contains 2 fuses. -
Page 10: Mounting Of Capping Head
INSTRUCTION HANDBOOK FS10, FS32 All exhaust air is collected and exhausted through the air exhaust filter (2) A hose connection can be mounted in order to “remove” the process air form the capping area; but the machine will function even if no hose is mounted. -
Page 11: Mounting Of Bottle Tool
INSTRUCTION HANDBOOK FS10, FS32 3.3 Mounting of bottle tool Place the bottle tool on the bracket and mount the screw. Note: If the bottle tool is mounted too close to the machine the switch function will not work, see section 4.1 4 Adjustments 4.1 Adjustment of the height of the capping head... -
Page 12: Adjustment Of The Stroke Length Of Piston In Capping Head
INSTRUCTION HANDBOOK FS10, FS32 Connect compressed air and power. Turn power ON. Choose the spacer (D) which best fits the capping head on the machine. Place a bottle under the capping head – With NO stopper or cap in place. -
Page 13: Daily Use
FS10, FS32 5 Daily Use 5.1 Production START and STOP FS10/FS32 is ready for production start when: Section 3 has been completed The height of the capping head has been set (section 4.1) and the Power signal is ON 5.2 Starting-up and running... -
Page 14: Malfunctioning
6 Malfunctioning 6.1 Function errors / Trouble shooting FS10/FS32 is a relatively simple machine to operate and normally errors will be due to incorrect adjustment of certain functions. In the table below, the most common faults are described and what causes it. -
Page 15: Cleaning
Remove the capping head and the air tubes 7.3 Cleaning Guidance Correct cleaning of the FS10/FS32 is carried out by washing it off with water or detergents, using a lint-free firmly wrung cloth or lint-free paper towel; subsequently the machine is wiped off with a dry cloth. -
Page 16: Declaration Of Conformity
INSTRUCTION HANDBOOK FS10, FS32 10 Declaration of conformity Watson-Marlow Flexicon A/S Frejasvej 2-6 DK-4100 Ringsted Declare on our sole responsibility that the flex seal: Flex Seal type Item no Model FS10 93-100-100 63-100-020 FS32 93-100-110 63-100-050 to which this declaration relates is in conformity with the following standard(s):...