Cooling Operation; Time Set Function; Auto Swing Function; Maintenance Methods - andrews Polar Breeze Manual

Operating Instructions - Polar Breeze

Cooling Operation

1. Ensure that the drain tank is property placed in the unit.
2. Repeatedly press button to choose the cooling mode, LCD
window will show "cool". During the cooling operation, always
place the duct through an open window open to exhaust warm air
from the room.
3. Repeatedly press button to set a proper room TEMP at
17ºC-31ºC (or 63ºF-88ºF).
4. Press button to choose either high, middle, low fan speed.
5. Press button to adjust the air delivery direction. The LCD
window will show o
Note:
In order to Improve the cooling efficiency, be careful that:
a) If your room is directly exposed to the sun, draw the curtains.
b) Do not place near other heat source.

Time Set Function

With machine off (but power supplied), press
window will show ON, press the TIME button, set the time to
start as you like. The setting range is 1-12 hours.
To set time to stop the machine with the unit running, press
button, the LCD window will show OFF, press the TIME button
set the time to stop the machine as you like. The setting range is 1-12
hours.

Auto Swing Function

1. Press button, LCD window will show o
swing automatically.
2. Press once again button, the symbol o
window will disappear, the swing stops.
Attention:
Press buttons together for more than 2 seconds to lock the keys.
The LCD window will show a padlock, press the two buttons again to
unlock the keys, the padlock symbol will disappear.
Caution
1. When In cooling or dehumidifying mode, do not take out the water
tank, or the buzzer will sound and the compressor stops, and the
mode changes to FAN.
2. If you want to take out the tank before the water becomes full,
TIMER button
Press this button to set the time
for switch-on.
switch-off or to delete the timing.
TIME button
This button sets the
present time and timer.
button, the LCD
please stop the machine first, and wait for 3 minutes, to prevent the
dew water spilling Into the unit.
3. There Is a plastic pipe inside where the tank is placed. Do not
remove the stopper while the unit is working because the water is
used for cooling the copper duct.

Maintenance methods

Disconnect from power supply before any cleaning or maintenance.
and then begin to
Do not use chemical solvent (like benzene, alcohol glazer) to clean
surface of unit.
in the LCD

Air Filter

Clean the filter once every week.
Open the air filter (fig. 4). Take the air filter out of filter cover (fig. 5)
SWING button
Selection of this button will
determine the air delivery
in swinging mode or fixed
direction mode.
TEMP button POWER
This button sets the Indication light.
room temperature.
Fig. 4 Fig. 5
Click www.andrews-sykes.com
FAN SPEED button MODE button
Press this button will Press this button will select among the
choose high, middle or modes of cooling, dry or heating (or fan
low speed of air delivery. mode for the cooling-only model).
WATER FULL ON/OFF button
Indication light. Pressing this button will
turn the machine on or off.
Wash the air filter by immersing it in warm (about 40ºC) water with a
neutral detergent, rinse and dry it thoroughly in a shaded place.
Reattach the filter to the filter cover with the attachment hooks on the
inside surface of the cover.
Place the hooks at the bottom of the filter cover into the holes in the
case, push it back to its original position.

Water tank

Hold the handle in water tank and
draw out slowly. Pour out the water,
clean away any dirt with neutral
detergent. Wash and dry it carefully
and then push the tank back (fig. 6).

End of season operation

Clean filter
Clean all surfaces
Drain water tank
Run on fan only for 1hr
Check water tank is empty and clean
Stow cable and cover unit
or Call Us Free
Fig. 6
0800 211 611