Evolution R225DWS Original Instructions Manual
Hide thumbs
Also See for R225DWS:
- Original instructions manual (40 pages) ,
- Original instructions manual (117 pages)
Related Manuals for Evolution R225DWS
Summary of Contents for Evolution R225DWS
- Page 1 R225DWS Original Instructions Original written in UK English Date Published: 16 / 04 / 2018...
- Page 2 Evolution Power Tools Machine. not exhaustive) blades, cutters, drills, chisels Please complete your product registration or paddles etc. In no event shall Evolution ‘online’ as explained in the A5 online Power Tools be liable for loss or damage...
- Page 3 www.evolutionpowertools.com MACHINE SPECIFICATIONS MACHINE METRIC IMPERIAL Motor (230-240V ~ 50Hz) 710W 600-1500rpm Speed No Load 600-1500min Weight 5.8kg 12.8lb Dust Port Diameter 35mm 1-5/16 In. 9 x 13-13⁄16 x Tool Dimensions - Contracted (H x W x L) 230 x 250 x 1450mm 57-1/16 In.
-
Page 4: Labels And Symbols
LABELS & SYMBOLS Wear Ear Protection WARNING: Do not operate this machine if warning and/or instruction labels are missing or damaged. Contact Evolution Power Tools Wear Dust Protection for replacement labels. Note: All or some of the following symbols Read Instructions may appear in the manual or on the product. -
Page 5: Safety Precautions
Only use accessories that they do not have access to, and are not designed for use in this machine and/or those allowed to play with, this machine. recommended specifically by Evolution Power Tools Ltd. ELECTRICAL SAFETY (1.14) - Page 6 www.evolutionpowertools.com (2.2) 1) General Power Tool Safety result in serious personal injury. Warnings [Work area safety] b) Use personal protective equipment. a) Keep work area clean and well lit. Always wear eye protection. Protective Cluttered or dark areas invite accidents. equipment such as dust masks, non-skid b) Do not operate power tools in explosive safety shoes, hard hat or hearing protection...
-
Page 7: Additional Safety Instructions
www.evolutionpowertools.com unfamiliar with the power tool or these use of an approved face mask with replaceable Instructions to operate the power tool. filters when using this machine. Power tools are dangerous in the hands of You should always: untrained users. •... - Page 8 Check for misalignment or binding of moving parts, and any condition UNPACKING that may affect the machines operation. Any replacement parts should be Evolution Caution: This packaging contains sharp Power Tool approved, and fitted by a objects. Take care when unpacking. Remove qualified and competent technician.
-
Page 9: Machine Overview
www.evolutionpowertools.com MACHINE OVERVIEW 1. SWIVELLING SANDING HEAD 7. AUXILIARY D HANDLE 2. EXTENSION TUBE 8. MOTOR ‘ON/OFF’ SWITCH 3. HAND GRIP AREAS 9. MOTOR SPEED CONTROL 4. LED RING LIGHT 10. HOSE END CONNECTORS (X3) 5. MOTOR 11. DUST EXTRACTION HOSE 6. -
Page 10: Assembly And Preparation
www.evolutionpowertools.com ASSEMBLY AND PREPARATION SHORT REACH MODE WARNING: Only conduct the following procedures with the machine disconnected from the main power supply. Fitting the Flexible Dust Extraction Hose. • Loosen the sleeve nut. (Fig. 1) • Insert the Flexible Dust Extraction Hose into the machines main dust extraction tube/handle, and push it fully ‘home’... - Page 11 www.evolutionpowertools.com Note: The design of the ‘D’ handle is such that ergonomic positioning of the handle on the clamp is possible. This ensures comfortable operation for both right-handed and left-handed users. • Insert the Flexible Extraction Hose fully into the end of the Extension Tube and tighten the sleeve nut to secure it in place.
-
Page 12: The Machines Controls
www.evolutionpowertools.com THE MACHINES CONTROLS • The ‘ON/OFF’ slide switch (Fig. 9) is a latching type. Slide it forward to start the motor. Push forward and down on the central section of the switch to latch it in the ‘ON’ position •... -
Page 13: Operator Stance
www.evolutionpowertools.com OPERATOR STANCE • The operator should adopt a comfortable stance with their feet apart and firmly balanced. • Both feet should be on the ground or floor. It is not acceptable to have one foot on the floor and the other on a stand or ladder rung etc, as this precludes the operator from achieving a proper balanced stance. -
Page 14: Maintenance
www.evolutionpowertools.com • Keep the Sander in constant motion whilst the abrasive disc is in contact with the work surface. Use a steady, sweeping motion, allowing the rotating abrasive disc to ‘float’ over the work surface. Moving the Sander erratically or concentrating for too long on one area can also cause swirl marks or unevenness in the work surface. - Page 15 www.evolutionpowertools.com secure the Brush Skirt and lens into the Sanding Head. • Carefully pull and ease the Brush Skirt and lens from the Sanding Head. • Installation of a new Brush Skirt is basically the reversal of the removal process. •...
-
Page 16: Ec Declaration Of Conformity
In accordance with EN ISO 17050-1:2004 The manufacturer of the product covered by this Declaration is: UK: Evolution Power Tools Ltd, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. FR: Evolution Power Tools SAS, 61 Avenue Lafontaine, 33560, Carbon-Blanc, Bordeaux, France. - Page 17 www.evolutionpowertools.com NOTES...
- Page 18 www.evolutionpowertools.com Notes...
- Page 19 www.evolutionpowertools.com Notes...
- Page 20 Evolution Power Tools Ltd Evolution Power Tools LLC Evolution Power Tools SAS Venture One 8363 Research Drive 61 Avenue Lafontaine 33560 Longacre Close Davenport Holbrook Industrial Estate Iowa Carbon-Blanc Sheffield 52806 Bordeaux S20 3FR +44 (0)114 251 1022 +1 866-EVO-TOOL...
Need help?
Do you have a question about the R225DWS and is the answer not in the manual?
Questions and answers