Operation - Mitsubishi Electric Mr.Slim PEA-M100HAA Operation Manual

3. Operation

■ About the operation method, refer to the operation manual that comes with each remote controller.
3.1. Mode select
3.1.1. For wired remote controller
Cool Dry
*1 *1
*1 Operation modes that are not available to the connected indoor unit
models will not appear on the display.
*2 Single or dual set points will appear, depending on the indoor unit
model.
* Interlocked operation is performed in all the operation modes when
the ventilation unit is interlocked.
What the blinking mode icon means
The mode icon will blink when other indoor units in the same refrigerant
system (connected to the same outdoor unit) are already operated in a
different mode. In this case, the rest of the unit in the same group can
only be operated in the same mode.
3.1.2. For wireless remote controller
■ Press the operation mode (
operation mode 2.
Cooling mode
►
Drying mode
Fan mode
Heating mode
Automatic (cooling/heating) mode
Ventilation mode
Only indicated on the following condition
Wired remote controller used
LOSSNAY connected
Automatic operation
■ According to a set temperature, cooling operation starts if the room
temperature is too hot and heating operation starts if the room
temperature is too cold.
■ During automatic operation, if the room temperature changes and
remains 2 °C or more above the set temperature for 15 minutes, the
air conditioner switches to cooling mode. In the same way, if the room
temperature remains 2 °C or more below the set temperature for
15 minutes, the air conditioner switches to heating mode.
Cooling mode
15 minutes (switches
from cooling to heating )
■ Because the room temperature is automatically adjusted in order to
maintain a fixed effective temperature, cooling operation is performed
a few degrees warmer and heating operation is performed a few
degrees cooler than the set room temperature once the temperature is
reached (automatic energy-saving operation).
Auto Heat
Fan
*1*2 *1
) button ② and select the
15 minutes (switches
from heating to cooling)
Set temperature +2°C
Set temperature
Set temperature -2°C
3.2. Preset temperature setting
3.2.1. For wired remote controller
Preset temperature will be displayed either in Celsius in 0.5- or 1-degree
increments, or in Fahrenheit, depending on the indoor unit model and the
display mode setting on the remote controller.
<Cool, Dry, Heat, and Auto (single set point)>
Press button ⑧ [F2] to decrease the preset temperature.
Press button ⑨ [F3] to increase the preset temperature.
<Auto (dual set point)>
1
Press button ⑧ [F2] or ⑨ [F3].
F2 F3
F1
2
Press button ⑦ [F1] or button ⑧ [F2] to move the cursor to the
desired temperature setting (cooling or heating).
Press button ⑨ [F3] to decrease the selected temperature, and ⑩ [F4]
to increase.
F1 F1 F2 F2 F3 F3
3.2.2. For wireless remote controller
► To decrease the room temperature:
Press button ③ to set the desired temperature.
The selected temperature is displayed 3.
• Each time you press the button, the temperature value decreases by 1 °C.
► To increase the room temperature:
Press button ③ to set the desired temperature.
The selected temperature is displayed 3.
• Each time you press the button, the temperature value decreases by 1 °C.
• Available temperature ranges are as follows:
Cooling/Drying: 19 - 30 °C
Heating: 17 - 28 °C
Automatic: 19 - 28 °C
• The display flashes either 8 °C - 39 °C to inform you if the room
temperature is lower or higher than the displayed temperature.
Preset temperature
for cooling
Preset temperature
for heating
F4
Preset temperature
for cooling
Preset temperature
for heating
F4 F4
7