Related Manuals for Softing WireXpert Cat6A+Adapters
Summary of Contents for Softing WireXpert Cat6A+Adapters
- Page 1 User Manual Cat 6A+ Adapters Version: WireXpert4500_Copper_CAT6APLUS_IT_EN_201911 © Copyright 2019 Softing Singapore Pte Ltd...
- Page 2 Softing Singapore Pte Ltd 73 Science Park Drive #02-12/13 Cintech I Singapore Science Park 1 Singapore 118254 http://itnetworks.softing.com + 65 6569 6019 + 65 6899 1016 asia-support.itnetworks@softing.com The latest version of this manual is available in the Softing download area at: http://itnetworks.softing.com.
-
Page 3: Table Of Contents
Performing an AUTOTEST ................17 Understanding AUTOTEST ......................17 Managing test result(s) ................. 20 Viewing results on eXport PC software ..................20 Viewing results on PDF report ....................21 Declarations ....................22 Technical Support ..................25 © Copyright 2019 Softing IT Networks... - Page 4 Table of Contents This page is left intentionally blank © Copyright 2019 Softing IT Networks...
-
Page 6: Introduction
WireXpert 500-CU. 1.2 Safety precautions Read this manual before starting For damages due to improper connection, implementation or operation Softing refuses any liability according to our existing warranty obligations. Note This symbol is used to call attention to notable information that should be followed during installation, use, or servicing of this device. -
Page 7: Intended Use
1.4 About this document Read this manual before starting For damages due to improper connection, implementation or operation Softing refuses any liability according to our existing warranty obligations. 1.4.1 Document history... -
Page 8: Before You Start
Class FA/CAT 8 options Patch Cord Test adapters Softing recommends WireXpert to be calibrated annually. Starting from v7.4, WireXpert will remind the user to calibrate the units if the last calibration was more than one year ago. This notification can be closed by clicking the [OK] button, but will be displayed on every boot up until the units are calibrated. -
Page 9: System Requirements
Windows 7, 8.x or 10 (32 bit or 64 bit) Intel Core 2 Duo, 2GHz 1 GB of RAM 200 MB of free space of installation Microsoft .NET framework © Copyright 2019 Softing IT Networks... -
Page 10: Application Description
PoE is planned for a specific cabling installation. When using the CAT6A+ adapters, the general requirements such as maximum distance between links remains unchanged as per documented by the Standards. © Copyright 2019 Softing IT Networks... -
Page 11: Setting Reference
Tools menu. 3.1 Calibration for Permanent Link To ensure accuracy for DCRU measurements in Permanent Links, Softing has included a calibration artefact in the test kit. Calibration is only required when the adapters are paired for the first time, or when DCRU measurements are inconsistent after multiple use. - Page 12 6. Remove Calibration artefact from the LOCAL end. 7. Connect Calibration artefact to REMOTE end and press the [NEXT] button to proceed. 8. Press the [BACK] button to return to Tools menu or [NEXT] button to perform Calibration again. © Copyright 2019 Softing IT Networks...
-
Page 13: Configuring An Autotest
54, 78 Crossover at pairs 12, 36 for 2-pair cable 4. Click [OK] on Crossover Wiremap Selection screen to save selection. 5. Click [OK] on Test Option screen to save option. © Copyright 2019 Softing IT Networks... -
Page 14: Testing Guide For Permanent Link Testing
4.2 Testing Guide for Permanent Link Testing Permanent Link (PL) test is comprised of the connection from a patch panel to a telecommunication outlet (horizontal cabling) using Permanent Link test adapters at each end of the link under test. © Copyright 2019 Softing IT Networks... -
Page 15: Testing Guide For Channel Testing
5. Connect the LOCAL unit to the patch panel and REMOTE unit to the outlet using the patch cord connected to be used. 6. Press the [AUTOTEST] button to begin AUTOTEST. 6A+ Ch adapter Link under test 6A+ Ch adapter Patch Panel Horizontal Cabling Outlet LOCAL REMOTE © Copyright 2019 Softing IT Networks... - Page 16 “Installation Guide for eXport PC software” and “User Manual for eXport PC software”. Note Depending on the number additional options that are enabled, WireXpert may take a slightly longer time to perform accurate measurements of the parameters. © Copyright 2019 Softing IT Networks...
-
Page 17: Performing An Autotest
Select the additional options to view the detailed result of the parameter. DCRU Pair-to-Pair DCRU In-Pair If DCRU option is disabled, the Unbalance (UBL) P2P and In- Pair tabs will not be available. © Copyright 2019 Softing IT Networks... - Page 18 AUTOTEST when the selected crossover cable is used. AUTOTEST Passed with AUTOTEST Passed with AUTOTEST Passed with “Straight-through cable” “Crossover at pairs 12, 36” “Crossover at pairs 12, 36, selected. selected. 54,78” selected. © Copyright 2019 Softing IT Networks...
- Page 19 Unshielded cables are used in the Link and/or patch cords under test. Unshielded connectors are used. AUTOTEST Passed with “Shield AUTOTEST Failed with “Shield Test” enabled Test” enabled WireXpert will not continue with the AUTOTEST process if a shield integrity test FAIL is detected. © Copyright 2019 Softing IT Networks...
-
Page 20: Managing Test Result(S)
If DCRU option is disabled, the AUTOTEST. Unbalance P2P and In-Pair parameters will not be available. 5. Double-click on the result. 6. If DCRU option is enabled for an AUTOTEST, the parameters will be listed in the “Resistance” tab. © Copyright 2019 Softing IT Networks... -
Page 21: Viewing Results On Pdf Report
2. If DCRU option is enabled during an AUTOTEST, the parameters will be listed in the Wiremap test block in the report. PDF Test report indicating DCRU parameters. PDF Test report without DCRU parameters. © Copyright 2019 Softing IT Networks... -
Page 22: Declarations
Declarations Declarations © Copyright 2019 Softing IT Networks... - Page 23 Compatibility" (EMC directive). It meets the following requirements: Note A Declaration of Conformity in compliance with the above standards has been made and can be requested from Softing Singapore Pte Ltd. China ROHS The WireXpert device and its test components are China ROHS compliant.
- Page 24 The light source transmitted from the following fiber test modules – MPO REMOTE are classified as Class 1m lasers and have wavelengths between 302.5 nm and 4000 nm and are safe except when used with optical aids. © Copyright 2019 Softing IT Networks...
-
Page 25: Technical Support
Technical Support Technical Support Softing’s global presence ensures our customers receives sales and technical support anywhere around the information: https://itnetworks.softing.com world. For more The Americas Softing Inc. 7209 Chapman Highway Knoxville, TN 37920 Phone: +1 865 251 5252 E-mail: sales@softing.us Asia / Pacific Softing Singapore Pte.
Need help?
Do you have a question about the WireXpert Cat6A+Adapters and is the answer not in the manual?
Questions and answers