Drills - Bosch 1375-01 Catalogue

DRILLS.

The suitable drills for a very wide
variety of materials
HBM 55/1
Drill at constant speed for opti-
mised operational life
Motors with extremely long service
lives for economical work
HBM 57/1
HBM 57/2
HBM 65/1
HBM 77/2
The machines come equipped with a special 4-m-long cable without plug.
8
0 602 120 101 265 200 3
0 602 120 104 135 200 3
0 602 120 107 72 200 3
0 602 120 104 200 300 2
0 602 121 101 265 200 6
0 602 121 104 135 200 6
0 602 121 107 72 200 6
0 602 121 104 200 300 4
0 602 131 101 265 200 6
0 602 131 104 135 200 6
0 602 131 107 72 200 6
0 602 131 104 200 300 4
0 602 133 101 265 200 9
0 602 133 104 135 200 9
0 602 133 107 72 200 8
0 602 133 104 200 300 8
0 602 134 101 265 200 2
0 602 135 001 265 200 5/3
0 602 135 004 135 200 5/3
0 602 135 101 265 200 8/5
0 602 135 104 135 200 8/5
0 602 135 104 200 300 5/4
0 602 117 001 265 200 13
0 602 117 004 135 200 13
0 602 117 008 72 200 13
0 602 117 004 200 300 10
0 602 119 001 265 200 16/12
0 602 119 004 135 200 16/12
0 602 119 008 72 200 16/12
0 602 119 004 200 300 16/18
7 2450 260 150 0.9 1.7 1/2HH-20 UNF 55
7 2450 260 150 1.7 1.7 1/2HH-20 UNF 55
7 2450 260 150 3.2 1.7 1/2HH-20 UNF 55
7 3700 400 230 1.7 1.7 1/2HH-20 UNF 55
9 1350 260 140 0.9 1.7 1/2HH-20 UNF 55
9 1350 260 140 1.7 1.7 1/2HH-20 UNF 55
9 1350 260 140 3.2 1.7 1/2HH-20 UNF 55
9 2000 400 230 1.7 1.7 1/2HH-20 UNF 55
10 1350 470 310 1.6 2.0 1/2HH-20 UNF 57
10 1350 470 310 3.3 2.0 1/2HH-20 UNF 57
10 1350 470 310 6.1 2.0 1/2HH-20 UNF 57
10 2050 600 400 3.3 2.0 1/2HH-20 UNF 57
10 690 470 310 1.6 2.0 1/2HH-20 UNF 57
10 690 470 310 3.3 2.0 1/2HH-20 UNF 57
10 1000 400 310 6.1 2.0 1/2HH-20 UNF 57
10 1030 700 460 3.3 2.0 1/2HH-20 UNF 57
6 3300 400 270 1.6 2.0 M 13 x 1 57
10/8 1600/2400 400 270 1.6 2.0 1/2HH-20 UNF 57
10/8 1600/2400 400 270 3.3 2.0 1/2HH-20 UNF 57
10/8 900/1500 400 270 1.6 2.0 1/2HH-20 UNF 57
10/8 900/1500 400 270 3.3 2.0 1/2HH-20 UNF 57
10/8 1500/2200 600 400 3.3 2.0 1/2HH-20 UNF 57
13 510 600 440 1.6 2.8 Taper B 16 65
13 510 600 440 3.3 2.8 Taper B 16 65
13 510 600 440 5.9 2.8 Taper B 16 65
13 760 900 630 3.3 2.8 Taper B 16 65
23 216/512 950 700 2.8 5.6 Morse Taper 2 77
23 216/512 950 700 5.5 5.6 Morse Taper 2 77
23 216/512 950 700 10.0 5.6 Morse Taper2 77
23 328/775 1450 1050 5.5 5.6 Morse Taper 2 77
Your specialist dealer can provide you with information on the complete set of quality accessories.
1 1-speed drill Chuck with key 3 608 571 001
with three-jaw chuck
Clamping range 1–10 mm
1
1
1
1
1
1
1
1 1-speed drill Chuck with key 3 608 571 001
with three-jaw chuck
Clamping range 1–10 mm
1
1
1
1
1
1
1
1-speed drill with keyless
1 3 608 571 004
chuck
2 2-speed drill Chuck with key 3 608 571 001
with three-jaw chuck
Clamping range 1–10 mm
2
2
2
2
1 Chuck
1-speed drill with 1 608 571 027
speed handle.
Clamping range 1.5 –13 mm
1
Three-jaw chuck can be
Additional handle 1 602 025 022
ordered as a special
1
accessory.
1
2 2-speed drill with Tubular handlef (M 27 x 2) 1 600 763 010
cross handle.
Drill drift 3 601 030 002
2
Without chuck.
Suitable for bits with.
2
morse taper 2.
Three-jaw chuck can be
2
ordered as a special
accessory.
9