HardWare KIT noTe: Parts not shown to actual size and not to scale. Item description Allen Key Camp Nail Screw M6x16 Q Screw M5x10 Screw & Nut Hooks Wrench...
parTs lIsT noTe: Parts not shown to actual size and not to scale. Item description Item description Column Central Roof Bar Short Track Base Short Track Side Connector C Long Track Central Roof Connector C1 Long Track Canopy Roof Bar L Curtains Roof Bar With Angled End Mosquito Netting Roof Connector...
installation step 1 1.1 Install Side Connectors (I) on top of the Column (A) using Screws (Q). Repeat 4 times. 1.2 Install Columns (A) onto Base (H) using Screws (P). Repeat 4 times. Parts required for this step:...
Page 8
installation step 2 2.1 Attach Short Track (B) to Short Track (B1) using Screws and Nuts (R). Repeat 2 times. 2.2 Repeat step 2.1 using Long Tracks (C) and Long Track (C1). Parts required for this step:...
Page 9
installation noTe: It is imperative that the Side Connectors (I) are angled towards the center of the sun shelter. step 3 3.1 Install the tracks to the columns using Screws (P). Alternate between Track (B & B1) and Track (C & C1) until structure is completed. Parts required for this step:...
Page 10
installation CaUTIon: ImporTanT: You must anchor the sun shelter before installing the roof. Unit must be anchored on a hard surface for the warranty to be valid. step 4 4.1 Anchor the sun shelter before installing the roof as follow: Grass surface: Use included Camp Nails (O) to anchor Base (H) previously installed on your Column (A).
Page 11
installation step 5 5.1 Slide Central Roof Connector (J) onto the middle of the Central Roof Bar (G). 5.2 Insert Roof Connectors (F) on each end of the Central Roof Bar (G). Parts required for this step:...
Page 12
installation step 6 6.1 Insert one end of Roof Bar (D) into the angled bar of Roof Connector (F). Repeat 4 times. 6.2 Install the roof structure you just built by inserting the end of Roof Bar (D) onto Side Connector (I). Parts required for this step:...
Page 13
installation step 7 7.1 Insert the Roof Bar (E) to Roof Connector (F). Repeat 2 times. 7.2 Insert the Roof Bar (E) to Roof Connector (J). Repeat 2 times. 7.3 Align the pre-drilled hole in Roof Bars (E) with the pre-drilled hole in the Roof Tracks (B & C). ensuring that the angled ends are facing downward.
Page 14
installation step 8 8.1 Place Canopy (K) over the roof structure 8.2 Align the openings in the side flaps of the Canopy (K) with the ends of the Roof Bars (E) previously done in Step 7.3 remove the Screw (P), overlap the flap with the opening and re-insert and tighten the screw so that the Canopy is secured onto the crossbeam tracks.
Page 15
installation noTe: Each 10ft side will have a total of 24 hooks between the mosquito netting and the curtains and the 12ft side will have a total of 28 hooks between the mosquito netting and the curtains. step 9 9.1 Install Hooks (S) along the eyelets of the Curtains (L) and Mosquito Netting (M). 9.2 Install Curtains (L) from the inside of the sun shelter along lower tracks of Tracks (B, B1, C &...
Page 16
Please refer to part numbers when reordering For questions or comments about product: Email: service@hengyatrade.com or Call toll-free: 1-855-379-7070 Made in / Hech en CHINA for Kmart Corporation, Hoffman Estates, IL 60179 See our extensive assortment of outdoor living products on-line at www.sears.com and www.kmart.com...
Need help?
Do you have a question about the Privacy 780-06019874-4 and is the answer not in the manual?
Questions and answers