Advertisement
Quick Links
Advertisement
Related Manuals for MICROMATIC ROTAC LONG ARM
Summary of Contents for MICROMATIC ROTAC LONG ARM
- Page 1 Micromatic LLC RotacTippers.com 525 Berne St Berne, IN 46711 1-260-589-2136 x3211 customerservice@micromaticllc.com ROTAC WASTE CART TIPPER Part Numbers: A010240 SAFETY WARNINGS Model: LONG ARM Installation, Service, and Use Manual Page 1 of 10 26-18-1006 rev.- Model: LONG ARM...
- Page 2 Micromatic LLC RotacTippers.com 525 Berne St Berne, IN 46711 1-260-589-2136 x3211 customerservice@micromaticllc.com Page 2 of 10 26-18-1006 rev.- Model: LONG ARM...
-
Page 3: Installation Preparation
1.) Please read this manual completely and familiarize yourself with all of the necessary procedures. Contact Micromatic LLC at (260) 589-2136, ext. 3211, if there is a question. 2.) To install the waste cart tipper onto the truck to the installation dimensions stated in this service manual requires an empty truck parked on a smooth and level surface. - Page 4 Micromatic LLC RotacTippers.com 525 Berne St Berne, IN 46711 1-260-589-2136 x3211 customerservice@micromaticllc.com ➢ THERE ARE NO OTHER WARRANTIES THAT EXTEND BEYOND THE WARRANTY HEREIN CONTAINED and no statement, oral or written, inconsistent with this warranty is binding on the Seller. No agent, employee, or representative...
- Page 5 Micromatic LLC RotacTippers.com 525 Berne St Berne, IN 46711 1-260-589-2136 x3211 customerservice@micromaticllc.com TIPPER SPECIFICATIONS Note: Product specifications subject to change without notice. Tipper Part Numbers A010240 (with Weld Plate) Model Name LONG ARM Mounting Weld Plate Part Number A010233 (Included with A010240) ANSI Z245.60 Type B-US Two-Bar Carts...
- Page 6 Micromatic LLC RotacTippers.com 525 Berne St Berne, IN 46711 1-260-589-2136 x3211 customerservice@micromaticllc.com TIPPER DIMENSIONS – SHOWN IN THREE (3) POSITIONS Recommend temporary mounting and performing a test fit and can pick up before fully welding mounting plate into place. Note: Be sure and account for chassis sag when loaded.
- Page 7 Running without a flow control device can be dangerous and lead to damage to the tipper and waste can. o Recommended speed is a cycle of 6-8 seconds. o Micromatic sells a flow control – see Service Parts section. ➢ WARNING:...
-
Page 8: Maintenance
Micromatic LLC RotacTippers.com 525 Berne St Berne, IN 46711 1-260-589-2136 x3211 customerservice@micromaticllc.com TIPPER MOUNTING OPTIONS The standard tipper base mounting plate is equipped with one mounting pattern: MAINTENANCE Lubrication ➢ Pivot joints are equipped with six (6) easy access grease zerk fittings. -
Page 9: Service Parts Kits
Berne, IN 46711 1-260-589-2136 x3211 customerservice@micromaticllc.com SERVICE PARTS KITS (IF YOUR PARTS DIFFER FROM THOSE SHOWN, PLEASE CONTACT MICROMATIC LLC. CUSTOMER SUPPORT AT (260)589-2136 EXT. 3211 FOR PROPER REVISION OF REPAIR MANUAL) • SEAL KIT FOR ACTUATOR = 450687-K1 •... - Page 10 Micromatic LLC RotacTippers.com 525 Berne St Berne, IN 46711 1-260-589-2136 x3211 customerservice@micromaticllc.com ➢ Refer to repair procedure Repair Manual - HS-1.5 THRU HS-015 to carry out maintenance on the 450687-S-B rotary actuator with seal kit 450687-K1. Please contact Customer Service or go to http://www.rotactippers.com.