Page 1
FE1000 Wireless Adjustable Base OWNER’S MANUAL Installation & Operation Patent Pending Serial No. 2-Year Parts and Labor on entire base Warranty.
CONTENTS Safety & Warranty Warnings Parts List FE1000 Electronics Quick Reference Guide Installa on Guide 9-10 FE1000 Remote Control Instruc ons PAIRING REMOTE Synchronizing Two Bases Headboard Bracket Installa on Guide Troubleshoo ng 15-16...
Safety & Warranty Warnings A en on: Read the following informa on before using this product . Failure to use a surge protec on device could compromise safety or cause product malfunc on and could void the electrical por on of your warranty. Electrical surges are by far the biggest cause of problems with electrical circuits.
Page 5
PACEMAKER WARNING: The massage units in this bed produce mechanical vibra ons that this warranty; (d) to damage to ma resses, fabric, cables, electrical cords or items supplied by dealers. Contact the dealer for warranty informa on on these items; (e) if there has been any modi ca on of the adjustable bed without prior wri en consent by nisco;...
Page 6
NISCO CO., LTD (“nisco”) warrants this adjustable bed to the consumer who is the original purchaser (the “purchaser”), subject to the terms and condi ons set forth herein. This warranty begins on the “warranty commencement date” which is the date of purchase for new unused beds and the date of manufacture for beds that have been used as oor or display models.
Page 7
PRODUCT RATINGS: The bed li motors are not designed for con nuous use of more than 2 minutes in an 18 minutes period, or approximately 10% duty cycle. Any a empt to circumvent or exceed this ra ng will shorten the life expectancy of the product and may void the warranty. WEIGHT UNITS: The limita on for this adjustable bed is 850 lbs.
Page 8
TO REDUCE THE RISK OF SHOCK, BURNS, FIRE OR INJURY: Make sure the base is in a at posi on and the vibra ng motors are turned o before unplugging the bed base from the power source. Always unplug the base from the electrical outlet before cleaning or servicing the base . If the cord or plug is damaged, discon nue use of the bed base.
Parts List All electronics and components that need to be installed are located in boxes under the founda on or a ached to the frame. Before discarding the packing materials, ensure that all the parts are accounted for. (2) 9-Volt Ba eries Bed Legs &...
Installation Guide 2. To install all six legs (seven for king/CK size,see image A on page 10) , thread the bolt of the leg to the nut on the founda on frame, and ghten by hand. DO NOT OVERTIGHTEN. Two people are required to set up the founda on. NOTE: To avoid damage to the founda on, always open the carton while the bed is in the at posi on.
Page 13
Middle Leg on King/CK Size Only 5. Carefully ip the founda on over onto its legs. Important: Two people are required to move the founda on. Head Do not drag across the oor. Do not rest frame on its side; excessive pressure may damage the legs.
PAIRING REMOTE The original remote that comes in the box is already paired to the founda on. No further ac on is required. In the event that the remote is not paired with the founda on, follow the steps below. STEP 1 Make sure the ba eries work ne.
Synchronizing Two Bases STEP 1 STEP 3 Plug A and B bases to power source. Pair remote A to Base B, then base A and base B can be simultaneous operated by Remote A. Base B Base A Base B Base A Remote A Remote A...
Headboard Bracket Installation Guide Headboard brackets are an op onal accessory and are not included. A 1/2'' (13 mm) socket and 1/2'' (13 mm) crescent wrench are necessary to complete installa on. HEADBOARD BRACKET COMPONENTS (2) Headboard Brackets (2) T-Brackets (12) Short Bolts (12) Nuts STEP 2...
Troubleshooting In the event that the power founda on fails to operate, assess the symptoms and possible solu ons provided in the chart below. SYMPTOMS SOLUTIONS Verify that the power cord is plugged into a working, grounded electrical outlet. Test the Remote control illuminates and appears to be outlet by plugging in another working appliance.
Page 19
In the event that the power founda on fails to operate, assess the symptoms and possible solu ons provided in the chart below. SYMPTOMS SOLUTIONS Check ba eries in wireless remote control, replace with two (2) new AAA ba eries if necessary.
Need help?
Do you have a question about the flex EZZ FE1000 and is the answer not in the manual?
Questions and answers